D-Link Forums
The Graveyard - Products No Longer Supported => Routers / COVR => DIR-655 => Topic started by: duffer on July 28, 2011, 03:27:38 PM
-
I am having some issues, and I can't figure out how to solve them.
I have several computers on my home network.
1. MAC Pro Tower Running OS X 10.7
2. Dell Laptop w/internal Wireless connector, running WIN 7, 64 bit
3 Two (2) HP Desktops w/integrated wireless connectors, running WIN 7, 64 bit
4. Dell Desktop w/d-Link wireless "N" card, running WIN XP
5. Dell laptop w/dLink "N" wireless card, running WIN XP
I am also running the dLink Print server w/2 HP laser jet printers
I am also using Network Magic on all of the PC's, and Network Magic Add-on for the MAC
Here's my problem:
1. My MAC only sees my internet connection, my router and my tower (MACPro). It can print successfully to both of the networked printers. It cannot see any of the computers (PC's) in the network, even though they are all turned on.
2. My PC's can see all of the computers on the network, including MACPro, but I cannot get any of them to print through the Print Server.
My print server is PS-4AA440, and the two printers are connected to PS-4AA440-P1, and PS-4aa440-P2. I am not using the "U" connection on the print server.
I am assuming that I am doing something wrong, because the d-Link system has always been very user friendly. I am trying to get my MAC to see the rest of the computers on the network, and I am also trying to get my PC's to print on both of the printers on the Print Server.
Needless to say any suggestions and/or direction to correct this problem is greatly appreciated.
Thank you.
-
I recommend not using Network Magic. It's really not needed.
Ensure DNS IP addresses are being filled in under Setup/Internet/Manual?
Turn off QoS options.
Turn off Advanced DNS Services if you have this option.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices on the router.
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP.
-
OMG.
Thank you.
Now I have to figure out how to do this. Is this all done in router set up. Does it affect the Print Server.
Does it matter if I don't have d-Link adapters in all of the computers? My MAC is hardwired to the DIR-655.
Should I delete Network magic from all of the computers and then start this? Sorry to sound so ignorant, but I am. Is there a tutorial to do this? I really do appreciate your response, but I am concerned that I might mess up.
-
I would remove network magic first from all and then start.
I have my mac book pro wired and wireless.
I haven't tried OSX 10.7 yet. I'm getting it though.
HW shouldn't matter. Just got to make sure the IP addresses are set up on the router.
I recommend turning off all devices before you start accept for one PC connected to the router.
-
Sorry to sound so incompetent, but I am. Should I light off all of the computers and then remove Network Magic from them, one at a time and then shut them down? I have 6 computers (1 MAC Pro Tower hardwired to the router, 3 PC's, all wireless, 2 of them running WIN 7 and one running WIN XP, and 2 laptops, one running XP and one running 7). I am also using a DP300U print server, do I have to do anything special with that? A lot of my stuff has been around for a while, will I still be able to use my disks (or will I even need them)?
I only have my MAC running wired, is there an advantage to running both wired and wireless?
I did run my network for a long time without NM, but got it when it was offered for free.
Again, thank you for your direction and patience.
-
yes, remove the network magic from all PCs then turn them off and go to one PC. Set it up for reserved IP addressing on the router. Once you have one PC done, turn the next one on and do the same on the router. Turn the Print server on lastly and give it an IP address on the router as well.
-
Thank you. Will try to do this on the weekend. Again, I really appreciate your assistance.
-
Yes, I agree. Network magic is baaaad. Total bloatware.
-
Keep us posted, if you get in to something that your unsure about ask questions and will help out. If need be, someone can teamviewer.com in with you can help you get the router setup with you.
-
HOORAY!!!
Thank you so much. I got rid of NM and now have my wired computer (MAC) working off of the DIR-655, as well as my new laptop running WIN 7. The next thing I need to do is to get these two computers, along with some of the others if need be, to recognize my DP-300U d-Link print server that has two different printers on it. I have the Print Server directly wired into the DIR-655 (which I think is PS- 4AA440), and the two printers are on ports PS-4AA440-P1 and PS-4AA440-P2. Right now the print server is connected to the DIR-655, and the two printers are connected to the Print server. I have not turned the power on to the print server. Can you possibly bear with me for a bit more and tell me how to get my MAC (hard wired) and my Laptop (wireless) to connect to these printers through the Print Server?
Again, thank you very much.
-
I am able to get my MAC to print through the Print Server to both printers, and I can get my one laptop running WIN XP SP3 to do the same. I cannot get my computers running WIN 7 to do so. Am I missing something really basic here?
-
Check to make sure that Firewall settings in Windows 7 is open to connections for the print server or Turn it off temp to test it out. Turn off any 3rd party Av or firewall programs while your setting up the printer server and printer to be sure.
-
Thank you. After deleting Network Magic, I have noticed that the network is faster. I went to install the printers, and found that I had a bunch of ports that I know that I added in my quest to get my WIN 7 laptop to print, and now I think I need to get rid of them, but can't figure out how to do that.
I have determined that the ip address for the print server is 192.168.0.10, but haven't been able to determine the ip for the printers that are attached to the server. The two ports are called PS-4AA440-P1 and PS-4AA440-P2 (they have parallel connectors). The printers are hooked up to those ports, but I'm not sure how I can access their pi's. This basically, I think, may be my final problem getting these things to print. Hopefully when I can get rid of all the ports that I created (TCP/IP) ports and I can find the ip's of the two printers, I will be in business. Does this sound like a plan?
Again, thank you for all your help, I really appreciate it.
-
To delete the ports that are not needed, you need to make sure that a different port is already selected and in use. Once you do this, go into properties/ports tab and right click on the port you want to delete to highlight it. Then select delete. I should remove it.
You might want to contact the maker of the print server to see how it's set up. I presume that you should use the IP of the print server then some how you might need a setting or software setting to tell it to use what ever the printer port is connected too on the print server.
-
You have probably forgotten more than I will ever know about this set up. I really do appreciate your help and patience. One of the problems might be the print server I am using. It is the dLink DP-300U, which is 6 months past its end of service. I have been able to get the ip of the print server (192.168.0.10), but, beyond that, I have not been able to get the ip's of either of the two parallel printers that I have hooked up. One of the printers is a HP 1200 PS and the other is a HP 1300 PCL. The ports for the printers are PS-4AA440-P1 and PS-4AA440-P2. When I use the ip for the server, I can only get one of the printers to work, the one attached to the P1 port, regardless of which printer it is. This is all happening under WIN 7. The MAC has no problem printing to either printer as it reads both of them. Since there is no support for the DP-300U I'm not sure where I can go. I would really like to be able to select both printers simply because there are times when more than one person is printing.
Again, I really thank you for all you've done. I think I'm getting closer, but still have that gap to frustrate me.
-
I see there is a web page for the DPU 300. Not having used one before, not sure what it takes to set this up right for Windows. I have had some experience with HP Jet Direct and remember that they use the IP address then a port number after it and they use specific drivers for the Jet Direct that allows the ports to be used independently. Are there drivers for the printers for Windows 7? or you using generic drivers?
-
I would also check out the DPR-1260 forum as well and someone there might beable to give you some info on the DPU-300.
-
ftp.dlink.co.uk/dp_print_servers/dp-300u/dp-300U_manual.pdf (ftp://ftp.dlink.co.uk/dp_print_servers/dp-300u/dp-300U_manual.pdf)
That is the URL for the manual....
-
Thank you again for all the help. From what I have gathered, the issue is with the DP-300U Print Server and WIN 7. The DP-300U is at end of life service (this happened last October). While I am no expert at this, the opinions of others feel that the problems are related to the fact that there are no firmware updates to handle WIN 7. I have been able to get one printer to print using the IP of the server (192.168.0.10). I cannot get it to read the IP's of the two printers connected to the server. For now this will work as the other computers on the network that need printers, all have their own printers, this is a luxury, but I have them, they work, so why shouldn't I use them. It would just be a bit more sensible to have the printers on the server server the entire network. The removal of Network Magic seems to have helped , along with getting rid of some very large files associated with the program.
Again, I thank you for all your help. One final thing, is there a good print server out there that will not break the bank that will work with my DIR-655? My present printers are Parallel Port Printers, so I would need those ports, but I would assume in the future that as my printers die, I will be connecting with USB printers.
Thank you again.
-
Hi,
I know with my Brother all-in-one laser MFC-7820N, their software sets up a server item by default. But I have had much better luck changing it over to use an IP address I set up in the router, and then on each PC to print to it.
I am not sure if the Dlink unit you are using allows you to set up a LAN IP for each printer, but if it does, then you have to go back in Windows and setup each printer to use that specific IP you set up in the print server.....
The challenge is that the DLink unit has only one ethernet cable going to it, and has to be able to provide both IP addys to the router.... Using a server item gets around this in software apparently....
-
Use a DHCP reservation for your printer, then the IP will never change. You set the printer up for Auto DHCP but the reservation will give it the same IP so you don't have to monkey with the port settings after the inital installation of the printer software.
-
OMG, this sounds like it will solve my problem. The only thing limiting my doing this is my very limited expertise in work with DHCP. The alternative of hooking the two printers up to the router might be impractical as both of the current printers are parallel printers and do not have an ethernet port that would allow me to connect to the router. How would I set up the DHCP reservation for the two printers. I have gotten one of the printers to work from a WIN 7 Computer through the print server, using the print server's IP, but would prefer both. My MAC has no problems accessing either printer.
Again, thank you for all the help and direction, I am learning a lot, just hope I can remember it all.
-
A DHCP Reservation is used to give any system hooked to the router the same IP address everytime the system is cxonnected to the network. The page for doing this on the router's admin pages is Setup>Networking toward the bottom of that page.
I bought a refurbished color laser printer with a Ethernet connection about 6 years ago and that has been humming along ever since (got tired of buying inkjet cartridges only to watch them dry out). Set up a reservation for the printer and don't have to worry about reconfiguring any printer ports.
You could also look at some of the printers that have built-in WIFI.
-
I think the DP-300U only uses a single IP address and then uses (forgive me here) a NetBios type of Server name to differentiate between the 2 LPT ports and the 1 USB ports it can serve to....
Apparently, the Apple Mac handles this more easily than Windows does....The 300U is supposed to work with Vista, but it doesn't say anythig about Windows 7 compatibility.
I think you should be able to create Port settings for a Network Printer in Win7 if you have that information available to you ahead of time, as you likely have to set the Server address up Manuaully when you Run the Add-a-Printer wizard in Win7.... If you read thru the 300U manual, it Describes how to set up the Server Names to each LPT port.... Then you likely have to set up a New port for each Printer so that it would "resemble":
//DLink-300U/LPT1 for you First Printer
//DLink-300U/LPT2 for your Second Printer
OR If you use IP addys...
//192.168.0.10/LPT1
//192.168.0.10/LPT2
The Exact Server Name and LPT port name will vary based on your 300U setup.
I "Think" you should be able to get both LPT printers to work in Win7, altho it likely will not be an automated process....
-
YES! Went through the Administrator's Manual, and found out that if I use the WIN XP set up (pp. 20-23) it works. Now recognizes and prints on both printers.
Thank you again for all your help.
-
Glad you got it all working. Enjoy.
-
Thank you. I couldn't have done it without your help.
-
Come back and visit sometime.