D-Link Forums
The Graveyard - Products No Longer Supported => Routers / COVR => DIR-615 => Topic started by: yeng on May 21, 2012, 12:14:12 AM
-
Hi,
While playing on Diablo 3 using DIR-615, it will always get disconnected from server after 2 to 20 minutes.
The router firmware version is 7.12.
Thanks.
-
Welcome! (http://forums.dlink.com/index.php?topic=42487.0)
What Hardware version is your router? Look at sticker under router.
What region are you located?
Are you wired or wireless connected to the router?
What ISP Service do you have? Cable or DSL?
What ISP Modem do you have? Stand Alone or built in router?
What ISP Modem make and model do you have?
If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.
To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged.
If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.
Some things to try:
Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options. Advanced/QoS or Gamefuel.
Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
Enable uPnP and Multi-cast Streaming under Advanced/Networking.
Wireless Installation Considerations (http://forums.dlink.com/index.php?topic=48327.0)
What wireless modes are you using? Under Setup/Wireless/Manual.
Try single mode G or N or mixed G and N?
Channel Width set for Auto 20/40Mhz or try 20Mhz only.
Try setting a manual channel to a open or unused channel.
What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto.
What wireless devices do you have connected?
Any cordless house phones?
Any other WiFi routers in the area? Use InSSIDer (http://www.metageek.net/) to find out.
Turn off WISH, and WPS under Advanced.
Turn off Short GI, WLAN Partition,and Extra Wireless Protection if you have it. Under Advanced/Advanced Wireless.
Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic.
Turn off all devices accept for one wired PC while testing.
Check cable between Modem and Router, swap out to be sure. Cat6 is recommended. (http://www.networkcablingdirectory.com/articles/structured-network-cabling-id_1151.htm)
-
It is a constant problem--every 2 minutes, I'm getting disconnected from the Diablo servers. They say that the problem is with D-Link routers. Is there a download available?
I am running:
Windows 7 64 bit
Intel(R) Core (TM) i5 CPU 650 @ 2.30 GHz
Intel(R) HD Graphics
8.0 GB memory
The issue began in earnest with their latest patch, however the problem began about 2 patches back (2 weeks ago).
Please tell me if D-Link is supporting this USB router and if a driver update will be made available. I have the latest drivers for this model (WdfCoInstaller01009.dll, DUBE100.sys).
thank you
Kimberly White
kendahke@hotmail.com
-
Can u answer some of the questions presented to the op and try some of the suggestions?
-
Any status on this?