D-Link Forums
Software => D-ViewCam => Topic started by: callmeig on December 21, 2012, 08:10:06 AM
-
I really need help. I have 3 DCS-932L connected to DviewCAM 3.3 Device pack 1.4.2. When I open the DviewCAM main console I have picture. When I activate network service (live streaming) options under port: 8080 and webserver port: 801, it allows a visual of the DviewCAM GUI but no live streaming over the internet. Current IP http://68.228.139.63:801
Router config:
-port fowarded
--801 192.168.1.105 (app running on computer)
--8010 192.168.1.110 DCS-932L
--8012 192.168.1.112 DCS-932L
--8013 192.168.1.113 DCS-932L
-
I really need help. I have 3 DCS-932L connected to DviewCAM 3.3 Device pack 1.4.2. When I open the DviewCAM main console I have picture. When I activate network service (live streaming) options under port: 8080 and webserver port: 801, it allows a visual of the DviewCAM GUI but no live streaming over the internet. Current IP http://68.228.139.63:801
Router config:
-port fowarded
--801 192.168.1.105 (app running on computer)
--8010 192.168.1.110 DCS-932L
--8012 192.168.1.112 DCS-932L
--8013 192.168.1.113 DCS-932L
You should be patient and read more before going berserk sending pms...
Software: D-ViewCam Device Pack v1.4.3 (for WW) (http://forums.dlink.com/index.php?topic=51643.msg193516#msg193516)
Updates:
•Add camera: DCS-2332L
•Fixed DCS-2132L would cause D-ViewCam shut down issue
•Fixed live view bug for DCS-930/932L/930L/910/920 (DBG12060162)
Installing the new Device Pack v1.4.3.1 should fix it. Please come back and post your results.
Links:
http://ftp.dlink.ru/pub/Multimedia/Software/D-View%20Cam%20v3/Device_Pack/ (http://ftp.dlink.ru/pub/Multimedia/Software/D-View%20Cam%20v3/Device_Pack/)
http://www.mmnt.net/db/0/0/ftp.dlink.fr/DCS/logiciel_de_surveillance/DCS-100_Software_D-ViewCam (http://www.mmnt.net/db/0/0/ftp.dlink.fr/DCS/logiciel_de_surveillance/DCS-100_Software_D-ViewCam)
-
did the download, but still same problem. btw thanx a lot for the latest releases. so when i run the console its all fine and dandy. but the minute i use an outside computer the web remote client shows up, i click remote live viewer and this shows up:
The connection was reset
The connection to the server was reset while the page was loading.
The site could be temporarily unavailable or too busy. Try again in a few
moments.
If you are unable to load any pages, check your computer's network
connection.
If your computer or network is protected by a firewall or proxy, make sure
that Firefox is permitted to access the Web.
-
(http://i1323.photobucket.com/albums/u582/Callme_Ig/wwwaccess_zps2708f78b.png)
(http://i1323.photobucket.com/albums/u582/Callme_Ig/wwwaccessafterGUI_zps1b20c0ab.png)
-
Can you confirm if "Remote Playback" is working or if it just returns the same error?
If none of those two services pages loads at all then it might be a browser incompatibility. Try IE6+ preferably IE9, x86 - 32 bit
Plus, if you're OUTSIDE THE LAN (not on the same local area network, which seems to be your case) you have to forward ports 5150 (live view) and 5160 (remote playback) to 192.168.1.105, that is the D-ViewCam server.
edit: Your server is working for me on IE9. So you have to do both, forward the ports and use another internet browser, can't get any easier that that.
-
well for one, your IP address is not up right now. I sent a ping from cmd, no response.
Second, you probably shouldn't bother using D view cam software.
Last, each camera must have a unique port. You router will only allow port 801 to go to 1 ip address. Set camera 1 as HTTP port 801, #2 as 802, and #3 as 803. Then you would just have to go to IP:801, IP:802, etc.
Also, 8080 is most likely a bad port as in my case, it is used by the router for remote management.