D-Link Forums

The Graveyard - Products No Longer Supported => Access Points / Extenders => DAP-1360 => Topic started by: funkyz77 on February 07, 2013, 12:58:27 AM

Title: DAP 1360 lock
Post by: funkyz77 on February 07, 2013, 12:58:27 AM

hi guyz..need some help here, i try to update device firmware(from 2.11 to 2.14).
Everything is running welll until finish, but now my device wont work, icon wifi is off(not blink), i can't control to that device and only lock icon is turned on.


can you figure it out... thanks before.

Title: Re: DAP 1360 lock
Post by: FurryNutz on February 07, 2013, 07:15:23 AM

Did you factory reset the DAP before and after the FW update?
Was the update sent using a wired connection?
Do you have access to the DAP UI at 192.168.0.50? Set up a static IP address on a PC and then directly connect to the LAN port in back and test.

Title: Re: DAP 1360 lock
Post by: funkyz77 on February 08, 2013, 12:38:58 AM

yes, i update using wired connection, 
already use IP 192.168.0.50 (default).. but still no response....
pls advs.

Title: Re: DAP 1360 lock
Post by: FurryNutz on February 08, 2013, 07:07:31 AM

If you can't seem to get a response from the DAPs web page, I would attempt one more factory reset and try with a different PC. If still noting, then you'll need to phone contact DLink support and get it into RMA.

Title: Re: DAP 1360 lock
Post by: funkyz77 on March 05, 2013, 08:23:47 PM

thanks for answer, but still no response after that, i tried to switch with another PC, still no response also.

i will contact by phone to ask this matter.

thanks.

Title: Re: DAP 1360 lock
Post by: FurryNutz on March 11, 2013, 09:27:06 AM

Any status on this?  ???

Title: Re: DAP 1360 lock
Post by: furlong on March 27, 2013, 02:10:55 AM

I can confirm the DAP-1360 (h/w B1) locks up after a while on f/w 2.14b05 . Revert to the more stable 2.11b29 . D-Link is obviously releasing firmware without doing the necessary testing.

Title: Re: DAP 1360 lock
Post by: FurryNutz on March 27, 2013, 07:13:27 AM

Was a factory reset performed both before and after sending the FW update file then set up from scratch?

Does this happen on any WiFi modes?
Any other WiFi routers in the area? Link> Use InSSIDer (http://www.metageek.net/) to find out. How many?

Quote from: furlong on March 27, 2013, 02:10:55 AM

I can confirm the DAP-1360 (h/w B1) locks up after a while on f/w 2.14b05 . Revert to the more stable 2.11b29 . D-Link is obviously releasing firmware without doing the necessary testing.

Title: Re: DAP 1360 lock
Post by: furlong on March 28, 2013, 12:15:46 PM

Quote from: FurryNutz on March 27, 2013, 07:13:27 AM

Was a factory reset performed both before and after sending the FW update file then set up from scratch?

Not sure if I did all that, but admittedly a pertinent question. Will do this and report result.

Cheers.

Title: Re: DAP 1360 lock
Post by: furlong on April 01, 2013, 04:15:51 PM

Ok, so the AP has been running stable since the procedure. I guess doing the factory reset before the f/w update did the job (I always do a reset after upgrading). Wouldn't have figured the importance of that.

Cheerio :)

Title: Re: DAP 1360 lock (RESOLVED)
Post by: FurryNutz on April 01, 2013, 04:17:26 PM

Glad its working for you.

Enjoy.