D-Link Forums
The Graveyard - Products No Longer Supported => Routers / COVR => DIR-655 => Topic started by: poley on October 23, 2013, 11:01:58 AM
-
I have an AppleTV (2gen), and after 30 minutes or so of watching a local stream (sometimes as few as 5 minutes), the wireless network disappears, and I have to reset the router to get it back. This is incredibly frustrating, and I would love a solution. I have reset the AppleTV to factory, so I don't think that's the issue.
Any advice?
-
Link>Welcome! (http://forums.dlink.com/index.php?topic=41537.0)
- What region are you located?
- Has a Factory Reset been performed?
- Was a Factory Reset performed before and after any firmware updates then set up from scratch?
- Was the router working before any firmware updates?
Internet Service Provider and Modem Configurations
- What ISP Service do you have? Cable or DSL?
- What ISP Modem Mfr. and model # do you have?
- What ISP Modem service link speeds UP and Down do you have?
- Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended. (http://en.wikipedia.org/wiki/CAT6)
Wireless Configurations
Links>Wireless Installation Considerations (http://forums.dlink.com/index.php?topic=48327.0) and Managing Signal Congestion (http://forums.dlink.com/index.php?topic=53228.0)
- Ensure the default (dlink) SSID name is changed. Can be anything and not something thats already in use by any neighboring WiFi routers. Under Setup/Wireless/Manual.
- What wireless modes are you using?
- 2.4Ghz Routers only: Try single mode G or N or mixed G and N?
- Channel Width set for Auto 20/40Mhz or try 20Mhz only.
- Try setting a manual Channel (http://en.wikipedia.org/wiki/Wireless_channel) to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear.
- What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES (http://en.wikipedia.org/wiki/Advanced_Encryption_Standard), so you might want to try TPIK (http://en.wikipedia.org/wiki/Temporal_Key_Integrity_Protocol) only or Auto TPIK and AES.
- What wireless devices do you have connected?
- Any cordless house phones?
- Any other WiFi routers in the area? Link> Use InSSIDer (http://www.metageek.net/) to find out. How many?
- If you have any of these options, Try turning OFF or ON Short GI (http://www.smallnetbuilder.com/wireless/wireless-features/30969-what-do-80211ns-optional-features-mean-for-you), WLAN Partition, HT 20/40 Co-exhistance and Extra Wireless Protection if you have it. Recommended settings are default. Under Advanced/Advanced Wireless.
- Enable WMM Enable (http://forums.dlink.com/index.php?topic=50738.0) Under Advanced/Advanced Wireless.
- Try setting Medium or Low power output settings and test again Under Advanced/Advanced Wireless.
3rd Party Security Software Configurations
- Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic.
- Turn off all devices accept for one wired PC while testing.
Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
6" minimum safe distance between devices.
-
Disabling short GI seems to have fixed it.
I'm in the US, on Time Warner Cable.
-
Glad you found a fix.
For future reference:
Router Troubleshooting Suggestions and Tips (http://forums.dlink.com/index.php?topic=54498.0)
Enjoy. ;)