D-Link Forums

The Graveyard - Products No Longer Supported => Routers / COVR => DIR-615 => Topic started by: ZubairKhokhar on November 24, 2013, 12:59:11 AM

Title: Problem configuring PPTP
Post by: ZubairKhokhar on November 24, 2013, 12:59:11 AM

I have a Dlink DIR-615 with 5.10.
I got a new connection with PPTP protocol and I had problems connecting. I changed the PPTP server address to an ip instead of red.connect.net.pk and it connected. Now the problem I'm facing is that it's connected  but there is still no internet access. It works just fine with the cable plugged to my laptop.
My ISP tells me to get a new router... Help me out.
It has dynamic ip.
MTU 1400.
DNS address 0.0.0.0 (I tried putting in the address but that didn't work as well)

Title: Re: Problem configuring PPTP
Post by: FurryNutz on November 25, 2013, 07:55:59 AM

Link>Welcome! (http://forums.dlink.com/index.php?topic=41537.0)

• What region are you located?
• Are you wired or wireless connected to the router?
• Has a Factory Reset been performed?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?
• What ISP Modem service link speeds UP and Down do you have?
• If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT (http://www.practicallynetworked.com/networking/fixing_double_nat.htm) and How NAT Works (http://cognitiveanomalies.com/cisco-nat-how-nat-works/). To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.
  Example of a D-Link router configured for PPPoE with ISP Modem bridged: PPPoE Configuration on Router (http://forums.dlink.com/index.php?topic=56344.msg219023#msg219023)
• Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values (http://forums.dlink.com/index.php?topic=53008.0)
• For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.

• Turn off ALL QoS (http://vonage.nmhoy.net/qos.html) or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS (http://en.wikipedia.org/wiki/Quality_of_service) or Gamefuel.
• Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
• Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
• Turn on DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench (http://forums.dlink.com/index.php?topic=53222.0)
• Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
• Ensure devices are set to auto obtain an IP address.
• If IPv6 (http://en.wikipedia.org/wiki/Ipv6) is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
• Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI (http://en.wikipedia.org/wiki/SPI) to test.
• Enable uPnP (http://en.wikipedia.org/wiki/Upnp) and Multi-cast Streaming (http://en.wikipedia.org/wiki/Multicast) under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
• Turn off WISH, and WPS under Advanced.
• WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
• Set current Time Zone, Date and Time. Use an NTP Server (http://forums.dlink.com/index.php?topic=48695.0) feature. Tools/Time.
• Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended. (http://en.wikipedia.org/wiki/CAT6)

Title: Re: Problem configuring PPTP
Post by: FurryNutz on December 02, 2013, 10:33:28 AM

Any status on this?  ???