D-Link Forums

The Graveyard - Products No Longer Supported => Routers / COVR => DIR-657 => Topic started by: olesolo on December 08, 2013, 08:04:54 AM

Title: Wifi and lan loses connection
Post by: olesolo on December 08, 2013, 08:04:54 AM

Hi,
I already try to change different settings in setup for lan and wifi but it doesn't help.
Sometimes internet connection just stops and after 20-30 sec appear again.
I tried 1.02 firmware but then returned back to 1.01 and it seems helped for a day or two and then problem come back again.

My log is here https://dl.dropboxusercontent.com/u/259602/dlink_log.txt

Title: Re: Wifi and lan loses connection
Post by: FurryNutz on December 08, 2013, 12:05:11 PM

Link>Welcome! (http://forums.dlink.com/index.php?topic=41537.0)

• What region are you located?
• Are you wired or wireless connected to the router?
• Was a Factory Reset performed before and after any firmware updates then set up from scratch?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?
• What ISP Modem service link speeds UP and Down do you have?
• Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values (http://forums.dlink.com/index.php?topic=53008.0)
• For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.

• Turn off ALL QoS (http://vonage.nmhoy.net/qos.html) or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS (http://en.wikipedia.org/wiki/Quality_of_service) or Gamefuel.
• Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
• Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
• Turn on DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench (http://forums.dlink.com/index.php?topic=53222.0)
• Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
• Ensure devices are set to auto obtain an IP address.
• If IPv6 (http://en.wikipedia.org/wiki/Ipv6) is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
• Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI (http://en.wikipedia.org/wiki/SPI) to test.
• Enable uPnP (http://en.wikipedia.org/wiki/Upnp) and Multi-cast Streaming (http://en.wikipedia.org/wiki/Multicast) under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
• Turn off WISH, and WPS under Advanced.
• WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
• Set current Time Zone, Date and Time. Use an NTP Server (http://forums.dlink.com/index.php?topic=48695.0) feature. Tools/Time.
• Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended. (http://en.wikipedia.org/wiki/CAT6)

Wireless Configurations
Links>Wireless Installation Considerations (http://forums.dlink.com/index.php?topic=48327.0) and Managing Signal Congestion (http://forums.dlink.com/index.php?topic=53228.0) and Good Neighbour Policy (http://forums.dlink.com/index.php?topic=10634.0)

• Ensure the default (dlink) SSID name is changed. Can be anything and not something thats already in use by any neighboring WiFi routers. Under Setup/Wireless/Manual.
• What wireless modes are you using?
• 2.4Ghz Routers only:[/b] Try single mode G or N or mixed G and N?
• Channel Width set for Auto 20/40Mhz or try 20Mhz only.
• Try setting a manual Channel (http://en.wikipedia.org/wiki/Wireless_channel) to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear.
• What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES (http://en.wikipedia.org/wiki/Advanced_Encryption_Standard), so you might want to try TPIK (http://en.wikipedia.org/wiki/Temporal_Key_Integrity_Protocol) only or Auto TPIK and AES.
• What wireless devices do you have connected?
• Any cordless house phones?
• Any other WiFi routers in the area? Link> Use InSSIDer (http://www.metageek.net/) to find out. How many?
• If you have any of these options, Try turning OFF or ON Short GI (http://www.smallnetbuilder.com/wireless/wireless-features/30969-what-do-80211ns-optional-features-mean-for-you), WLAN Partition, HT 20/40 Co-exhistance and Extra Wireless Protection if you have it. Recommended settings are default. Under Advanced/Advanced Wireless.
• Enable WMM Enable (http://forums.dlink.com/index.php?topic=50738.0) Under Advanced/Advanced Wireless.
• Try setting Medium or Low power output settings and test again Under Advanced/Advanced Wireless.

Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
6" minimum safe distance between devices.