D-Link Forums

The Graveyard - Products No Longer Supported => Access Points / Extenders => DAP-1320 => Topic started by: Inaki on May 01, 2014, 04:02:45 AM

Title: Can´t see the Wifi signal!!
Post by: Inaki on May 01, 2014, 04:02:45 AM

Dear All,

I have just purchased my first DAP 1320 N300 unit.??

Have connected it to mains but I don´t see in any of my devices the Wifi signal.

Could the unit be faulty??

I have also reseted it according to manual just in case but no no.

Any hints before I take it back to the shop to get a new one?

many thanks

Inaki

Title: Re: Can´t see the Wifi signal!!
Post by: FurryNutz on May 01, 2014, 07:15:25 AM

Link>Welcome! (http://forums.dlink.com/index.php?topic=48135.0)

• What Hardware version is your DAP? Look at sticker under DAP.
• Link>What Firmware (http://forums.dlink.com/index.php?topic=47512.0) version is currently loaded? Found on the DAPs web page under status.
• What region are you located?
• Are you wired or wireless connected to the router?
• Has a Factory Reset (http://blog.dlink.com/what-is-a-reset-button-when-should-i-use-it) been performed?

What mode are you using the DAP in? AP mode?

Wireless Configurations
Links>Wireless Installation Considerations (http://forums.dlink.com/index.php?topic=48327.0) and Managing Signal Congestion (http://forums.dlink.com/index.php?topic=53228.0) and Good Neighbour Policy (http://forums.dlink.com/index.php?topic=10634.0)

• Ensure the default (dlink) SSID name is changed. Can be anything and not something that's already in use by any neighboring WiFi routers. Under Setup/Wireless/Manual.
• What wireless modes are you using?
• 2.4Ghz Routers only: Try single mode G or N or mixed G and N?
• Channel Width set for Auto 20/40Mhz or try 20Mhz only.
• Try setting a manual Channel (http://en.wikipedia.org/wiki/Wireless_channel) to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions.
• What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES (http://en.wikipedia.org/wiki/Advanced_Encryption_Standard), so you might want to try TPIK (http://en.wikipedia.org/wiki/Temporal_Key_Integrity_Protocol) only or Auto TPIK and AES. Does any of the devices see the SSID if you disable WiFi security temporarily to test?
• What wireless devices do you have connected?
• Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by?
• Any other WiFi routers in the area? Link> Use InSSIDer (http://www.metageek.net/support/metageek-software-archives/) to find out. How many?
• If you have any of these options, Try turning OFF or ON Short GI (http://www.smallnetbuilder.com/wireless/wireless-features/30969-what-do-80211ns-optional-features-mean-for-you), WLAN Partition, Extra Wireless Protection and HT 20/40 Co-existence if you have it. Also testing with HT20/40Mhz Co-existence enabled will impact results as well. I prefer to use this option OFF. Recommended settings are default. Under Advanced/Advanced Wireless.

DAP Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building is preferred. Not in basements as building materials could interfere or hinder good signal propagation.

PC 3rd Party Security Software Configurations

• Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic.
• Turn off all devices accept for one wired LAN PC while testing.
• Disable any downloading client software managers, i.e. Torrents or similar.

PC Web Browser Configurations
What browser are you using?
Try Opera or FF? If IE 8, 9, 10 or 11, set compatibility mode and test again.
Disable any security browser Add-ons like No Script and Ad-Block or configure them to allow All Pages when connected to the router.
Clear all browser caches.
Be sure to log into the Admin account on the router.
Try turning off these features in Chrome:
Top right corner, little bars for options > Settings > Settings (on left) > Show advanced settings.
Uncheck these:
Use a web service to help resolve navigation errors
Use a prediction service to help complete searches and URLs typed in the address bar
Predict network actions to improve page load performance
Enable phishing and malware protection