D-Link Forums
The Graveyard - Products No Longer Supported => Routers / COVR => DIR-655 => Topic started by: gfreek on September 15, 2014, 01:22:08 PM
-
Before I call tech support, I have issues with new DIR-655, Exede Satellite internet, does not matter if I use IE, Firefox, Chrome, the wired computer pages load very slow or not at all, wireless connections are lost also, if I bypass the router and go from modem direct no problems.. Re staring router doesn't help, I did a reset. I've been using another DIR655 and it's been working fine for over a week... Need suggestions.. Thanks
-
Link>Welcome! (http://forums.dlink.com/index.php?topic=48135.0)
- What Hardware version is your router? Look at sticker under router.
- Link>What Firmware (http://forums.dlink.com/index.php?topic=47512.0) version is currently loaded? Found on the routers web page under status.
Internet Service Provider and Modem Configurations
- Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended. (http://en.wikipedia.org/wiki/CAT6)
- Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values (http://forums.dlink.com/index.php?topic=53008.0)
Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router. Besure to log into the Admin account on the router.
- Turn off TrueGigaBit Routing under Setup/Internet/Manual for those routers that have this feature for testing.
- Turn off ALL QoS (http://vonage.nmhoy.net/qos.html) or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS (http://en.wikipedia.org/wiki/Quality_of_service)
- Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
- Enable or Disable Use Unicasting (compatibility for some ISP DHCP Servers) and test under Setup/Internet/Manual. Disable may help with speed performance on higher speed ISP services.
- Turn OFF DNS Relay (http://forums.dlink.com/index.php?topic=45143.0) under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench (http://forums.dlink.com/index.php?topic=53222.0) and input new DNS addresses under Setup/Internet/Manual.
- Setup DHCP (http://forums.dlink.com/index.php?topic=58017.0) reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting and maintain consistency for applications that need to connect as well as mapped drives.
- Ensure devices are set to auto obtain an IP address.
- If IPv6 (http://en.wikipedia.org/wiki/Ipv6) is an option on the router, select Local Connection Only under Setup/IPv6.
- Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI (http://en.wikipedia.org/wiki/SPI) to test.
- Enable uPnP (http://en.wikipedia.org/wiki/Upnp) and Multi-cast Streaming (http://en.wikipedia.org/wiki/Multicast) under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
- Turn off WISH (http://forums.dlink.com/index.php?topic=40459.0), and WPS under Advanced.
- WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
- Set current Time Zone, Date and Time. Use an NTP Server (http://forums.dlink.com/index.php?topic=48695.0) feature. The DST setting is only needed in the NA region. Tools/Time.
-
Updated firmware, changed settings and it's been working. Thank you for your help...
-
Glad you got it working.
Enjoy. ;)