D-Link Forums

The Graveyard - Products No Longer Supported => Other D-Link Products => Topic started by: Nuno18 on April 11, 2015, 02:06:23 PM

Title: Dir-320
Post by: Nuno18 on April 11, 2015, 02:06:23 PM

Hello, not sure if this is the right section for a problem.

i currently have 100 mbs speed, and my dlink is only catching like 30- 50 mbs. was wondering if theres a way to speed it up

anyone knows?

Thanks. again sorry if im posting this in the wrong section

Title: Re: Dir-320
Post by: nettewurk on April 11, 2015, 05:23:55 PM

Theoretical speed of 100Mbps cannot be achieved due to some factors from interference, client adapter's specs, encryption/cipher mode,  etc and other factors affecting its throughput.  Attaining 50% or more speed would OK in my opinion.  The cable throughput would depend on both connecting terminals condition because both ends may have firewall or real-time scanner may put some lag in the transmission rate also.  If WiFi, DIR-320 we had in our office operates at WiFi b/g only so it can operate only at 54MBbps, max out.  Is the model or specs right?  Speed is mutually established by 2 terminals connecting.  The lower speed specs only would be attained even the rated speed of other end is greater than the other side.

Title: Re: Dir-320
Post by: Nuno18 on April 11, 2015, 06:30:10 PM

Quote from: nettewurk on April 11, 2015, 05:23:55 PM

Theoretical speed of 100Mbps cannot be achieved due to some factors from interference, client adapter's specs, encryption/cipher mode,  etc and other factors affecting its throughput.  Attaining 50% or more speed would OK in my opinion.  The cable throughput would depend on both connecting terminals condition because both ends may have firewall or real-time scanner may put some lag in the transmission rate also.  If WiFi, DIR-320 we had in our office operates at WiFi b/g only so it can operate only at 54MBbps, max out.  Is the model or specs right?  Speed is mutually established by 2 terminals connecting.  The lower speed specs only would be attained even the rated speed of other end is greater than the other side.

Sorry forgot to mention it, if i connect my modem to my PC directly. it reaches almost 100 mbs. im using cable not Wifi, i was lagging alot on my ps4 too. so i had it increased. but from what im seeing now my problem seems to be the router and not the internet itself.

Ye its a old router called DIR-320, least what it says below it  ;D tbh ive no idea what to do. i resetted it because i opened some doors for ps4 and enabled dmz. none of that worked. now that i increased the connection speed its working at 30% capacity. cable should reach at least 90 MB's

Title: Re: Dir-320
Post by: FurryNutz on April 13, 2015, 09:04:29 AM

Link>Welcome! (http://forums.dlink.com/index.php?topic=48135.0)

• What Hardware version is your router? Look at sticker under the router case.
• Link>What Firmware (http://forums.dlink.com/index.php?topic=47512.0) version is currently loaded? Found on the routers web page under status.
• What region are you located?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?
• Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
• What ISP Modem service link speeds UP and Down do you have? Link> Speed Testing Sites (http://forums.dlink.com/index.php?topic=48352.0)
• Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended. (http://en.wikipedia.org/wiki/CAT6)
• Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values (http://forums.dlink.com/index.php?topic=53008.0)

Is the Gaming feature enabled under Advanced/Advanced Networking?