D-Link Forums
The Graveyard - Products No Longer Supported => Routers / COVR => DIR-605L => Topic started by: dipeshpatel on July 10, 2015, 09:20:26 AM
-
well here is my router info.
Firmware Version : 2.05UI
Hardware Version : B1
Product Page : DIR-605L
my problem is:
i use PPPoE connection and i have user name and password and my Connection mode is always on.
but when i start my router its did not connect the internet.
i mean to say its not dial it self i manually login in to router then goto status menu and click on connect button then the internet is connected.
so is there any option in router that connect (dial) internet automatically.
previously i used 3 wifi routers and they connect internet automatically but in this n300 cloud router not connect internet automatically,
please help me with that
-
I am having exactly same issue. It's very annoying.Where do you live and which ISP? I am from Nepal.
I was about to start new topics with my issue but found yours. I have firmware updated to 2.06. Why it can't connect automatically to internet when power is ON? Alos thes is no setting to auto connect as well. Connection mode to "always" didn't help either. I previously had Netis router which didn't have single problem. But unfortunately it was damaged by power fluctuation. Is this Dlink router really bad?
-
PPPoA/E users have to manually input the PPP user name and PW into the router then it should connect it the PPP ISP modem is bridged. Please refer to the routers user Manual for setup and configuration of the router for use with PPP ISP connections.
-
I am using this modem from last 7-8 months and having same problem.
Its very disturbing and irritating. Please help me.....
-
Link>Welcome! (http://forums.dlink.com/index.php?topic=48135.0)
- What Hardware version is your router? Look at sticker under the router case.
- Link>What Firmware (http://forums.dlink.com/index.php?topic=47512.0) version is currently loaded? Found on the routers web page under status.
- What region are you located?
- Are you wired or wireless connected to the router?
Internet Service Provider and Modem Configurations
- What ISP Service do you have? Cable or DSL?
- What ISP Modem Mfr. and model # do you have?
- Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
- What ISP Modem service link speeds UP and Down do you have? Link> Speed Testing Sites (http://forums.dlink.com/index.php?topic=48352.0)
- By-pass the main host router and check internet connection by connecting a wired LAN PC directly to the ISP modem to verify connection access and ISP speeds.
- Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended. (http://en.wikipedia.org/wiki/CAT6)
- Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values (http://forums.dlink.com/index.php?topic=53008.0)
- For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.
- If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT (http://www.practicallynetworked.com/networking/fixing_double_nat.htm) and How NAT Works (http://computer.howstuffworks.com/nat.htm). Call the ISP and ask to see if the ISP modem can be bridged. To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Also check the routers DHCP IP address maybe conflicting with the ISP modems IP address of 192.168.0.1. Check to see if this is the same on the ISP modem, and if modem can't be bridged, change the DIR router to 192.168.1.1 or .0.254.
Example of a D-Link router configured for PPPoE with ISP Modem bridged: PPPoE Configuration on a Router (http://forums.dlink.com/index.php?topic=56344.msg219023#msg219023)
I recommend that you have your ISP check the cabling going to the ISP modem, check signal levels going to the ISP modem. For DSL or Fiber service lines, ensure that the ISP is using good working phone or cable lines to the DSL modem and that the phone lines are filtered correctly. For cable Internet, RG-6 coaxial cable is needed, not RG-59. Check for t.v. line splitters and remove them as they can introduce noise on the line and lower the signal going to the ISP modem. I recommend having the ISP service physically check the lines going from the out side to the ISP modem. Connecting to the ISP modem could result in a false positive as the signal to the modem could be just enough to that point then adding on a router, could see problems. The router operation is dependent upon getting good data flow from the ISP modem and the modem is dependent upon getting good signal from the ISP Service.
I am using this modem from last 7-8 months and having same problem.
Its very disturbing and irritating. Please help me.....