D-Link Forums

The Graveyard - Products No Longer Supported => Routers / COVR => DIR-600 => Topic started by: manimohanb on November 09, 2015, 06:06:52 AM

Title: Not able to connect to Seagate Wireless
Post by: manimohanb on November 09, 2015, 06:06:52 AM

I am using DLINK DIR-600M Hardware Version: C1 Firmware Version:3.01

When I try connecting its not able connect. Connection refused.

When see the seagate help it says enable Multicast streams. Do we have this in this version or If I want it what should I do?

Title: Re: Not able to connect to Seagate Wireless
Post by: FurryNutz on November 09, 2015, 07:20:49 AM

Link>Welcome! (http://forums.dlink.com/index.php?topic=48135.0)

• What region are you located?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router. Besure to log into the Admin account on the router.

• Setup DHCP (http://forums.dlink.com/index.php?topic=58017.0) reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting and maintain consistency for applications that need to connect as well as mapped drives.
• Ensure devices are set to auto obtain an IP address.
• If IPv6 (http://en.wikipedia.org/wiki/Ipv6) is an option on the router, select Local Connection Only under Setup/IPv6.
• Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI (http://en.wikipedia.org/wiki/SPI) to test.
• Enable uPnP (http://en.wikipedia.org/wiki/Upnp) and Multi-cast Streaming (http://en.wikipedia.org/wiki/Multicast) under Advanced/Networking. Disable uPnP for testing Port Forwarding (http://forums.dlink.com/index.php?topic=4235.0) rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
• Turn off WISH (http://forums.dlink.com/index.php?topic=40459.0), and WPS under Advanced.

Wireless Configurations
Links>Wireless Installation Considerations (http://forums.dlink.com/index.php?topic=48327.0) and Managing Signal Congestion (http://forums.dlink.com/index.php?topic=53228.0) and Good Neighbour Policy (http://forums.dlink.com/index.php?topic=10634.0)

• Ensure the default (dlink) SSID name is changed. Can be anything and not something that's already in use by any neighbouring WiFi routers. Under Setup/Wireless/Manual.
• What wireless modes are you using?
• 2.4Ghz Routers only: Try single mode G or N or mixed G and N?
• Channel Width set for Auto 20/40Mhz or try 20Mhz only.
• Try setting a manual Channel (http://en.wikipedia.org/wiki/Wireless_channels) to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions.
• What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES (http://en.wikipedia.org/wiki/Advanced_Encryption_Standard), so you might want to try TPIK (http://en.wikipedia.org/wiki/Temporal_Key_Integrity_Protocol) only or Auto TPIK and AES.
• Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by that maybe causing interferences?
• Any other WiFi routers in the area that maybe causing interferences? Link> Use InSSIDer (http://www.techspot.com/downloads/5936-inssider.html) to find out. How many? Use v3, its free.
• If you have any of these options, Try turning OFF or ON Short GI (http://www.smallnetbuilder.com/wireless/wireless-features/30969-what-do-80211ns-optional-features-mean-for-you), WLAN Partition, Extra Wireless Protection and HT 20/40 Co-existence if you have it. Also testing with HT20/40Mhz Co-existence enabled will impact results as well. I prefer to use this option OFF. Recommended settings are default. Under Advanced/Advanced Wireless.

Title: Re: Not able to connect to Seagate Wireless
Post by: manimohanb on November 09, 2015, 07:38:05 AM

Place: India,

ISP: ACT

Model: DIR-600M N150

Problem: Not able to find Multicast Stream option in "192.168.0.1" page

Title: Re: Not able to connect to Seagate Wireless
Post by: FurryNutz on November 09, 2015, 07:56:12 AM

Check the user manual to see if this feature is available on this model router. I other DIR series routers, it's under the Advanced/Advanced Networking page.

Title: Re: Not able to connect to Seagate Wireless
Post by: manimohanb on November 09, 2015, 07:59:36 AM

Thanks for the HELP Its about the Security option..

If I use  TPIK only then I am able to connect.. not even in Auto mode.. It very strange

Title: Re: Not able to connect to Seagate Wireless
Post by: FurryNutz on November 09, 2015, 08:02:03 AM

Can you test with AES only?

Possible that your devices isn't supporting of certain securiy modes...