D-Link Forums
D-Link Network Video Recorders => DNR-322L => Topic started by: mbouster on December 11, 2015, 12:23:08 AM
-
Hello,
I have a dnr-322l hardware revision A2.
I have six cameras
2) DCS-4601EV
4) DCS-4701E
From the DNR GUI I can find the cameras with their IPs but only in just one i can connect.
The others are trying to connect but no connection with them.
I have to mention that i can access all cameras with their IPs.
Can someone help me please?
-
DNS:
Link>Welcome! (http://forums.dlink.com/index.php?topic=48135.0)
- Link>What Firmware (http://forums.dlink.com/index.php?topic=47512.0) version is currently loaded? Found on the DNSs web page under status.
- What region are you located?
What Mfr and model is the main host router?
Is the DNR getting a Dynamic IP address from the main host router? I recommend using a Static IP address ON the DNR set to 192.168.#.32 or .22.
Ensure uPnP and uPnP Port Forwarding is enabled on the DNR and ALL DCS cameras.
-
Hello,
I have a dnr-322l hardware revision A2.
I have six cameras
2) DCS-4601EV
4) DCS-4701E
From the DNR GUI I can find the cameras with their IPs but only in just one i can connect.
The others are trying to connect but no connection with them.
I have to mention that i can access all cameras with their IPs.
Can someone help me please?
mbouster,
Just a few things to check:
- Make sure all the camera passwords have been input on the DNR-322L camera profiles (common culprit when there is no video)
- Verify the operation mode the NVR (NVR Only or NVR+File Server Mode) NVR only has better Recording performance.
- Make sure bandwidth on the local network matches the requirements set by the FPS setting on each cameras.
- Make sure you are within the Max recording performance limits of the DNR-322L current operation mode
Recording Limits according to the datasheet:
(http://images.dlink.com/new/articles/FORUMS/DNR-322L_Recording-Performance_Limits.png)
Let us know how it goes.
-
Hi guys,
Thank you very much for the responses.
The answers to your questions are :
The default username and password is set on all devices. In this way nothing to set on DNR-322L at this time.
NVR operation: only NVR
Frame settings are 25 frames / per second.
The router is DIR-816L. I am not on the location where the NVR and router are installed.
I will provide those information on Saturday 19.12.2015.
-
The answers to the questions below:
The main host router is
Device Type ZXDSL 931VII V3.0
Device Serial No. ZTEEG8EF1M03357
Batch No. T1
HW Version V1.0.0
SW Version V1.0.5_CYPR_home
BOOT Version V1.0.3
I connected on the main host router a Wireless AC750 Dual Band Cloud Router -MODEL DIR-816L
NVR has a static IP 192.168.9.164.
Details of NVR and firmware
Current NVR Firmware Version :
2.40
Firmware Date :
09/29/2015
Current NVR Device Pack Version :
2.0.13
Device Pack Date :
09/24/2015
UpNp is enabled
-
From the DNR GUI I can find the cameras with their IPs but only in just one i can connect.
Which one could connect? One of the DCS-4601EV or a DCS-4701E?
Forgive my ignorance, for I am new to the camera forum, but what is being attempted by the DNR when it connects to one of the DCS? Is it pulling info from a certain port? If so, is it possible that port can only be routed to the camera one at a time? Sounds like a issue with UPnP between the NVR and the DIR-816L.
The main host router is
Device Type ZXDSL 931VII V3.0
I connected on the main host router a Wireless AC750 Dual Band Cloud Router -MODEL DIR-816L
Are you going to try to access the NVR from off site or via app? If so, how do you have the DIR-816L connected to the ZXDSL? If neither is in AP/Bridge mode, then your going to run into double NAT issues. Is this a problem for you?