D-Link Forums

The Graveyard - Products No Longer Supported => D-Link Storage => DNS-320L => Topic started by: Brahim on August 22, 2016, 03:46:13 AM

Title: DNS320-LW A2 Update 1-07b04
Post by: Brahim on August 22, 2016, 03:46:13 AM

Hi

I connect to My dlink and the process request to me to up-date to the version 1-07b04 my DNS320-LW ver A2.
I have process. Since that My dns don't want to boot.
The power Led always flashing. The Fan  and HDD don't start.

Do you have any solution to restart it?

Regards
Bra

Title: Re: DNS320-LW A2 Update 1-07b04
Post by: ivan on August 22, 2016, 05:58:11 AM

First think check that the power supply is giving 12v @ 3A (you can test this by using another power supply that can supply 12v at, at least 3A- more Amps are OK).

If the power supply is OK then try using the reset button.

After that it starts to get complicated and require specialist tools.

Title: Re: DNS320-LW A2 Update 1-07b04
Post by: Brahim on August 24, 2016, 09:18:22 AM

Thanks for your reply.

Power is Ok.

I try to push reset button 20s and try to restart .

Always power flashing ( as per the manual it's booting status).

Regards

Title: Re: DNS320-LW A2 Update 1-07b04
Post by: ivan on August 24, 2016, 03:46:39 PM

OK, now the 'fun' begins.

Go to http://dns323.kood.org/dns-320l (http://dns323.kood.org/dns-320l) and read all on that page then have a look at items on the menu at the left.  You are going to need some equipment and some knowledge of low level kernel programming.  You will also need a copy of the firmware that you replaced to enable you to get back to your previous state.

Good luck.

Title: Re: DNS320-LW A2 Update 1-07b04
Post by: feuz on August 27, 2016, 05:56:22 AM

Hi,

i've the same issue, have you found a solution ?

Title: Re: DNS320-LW A2 Update 1-07b04
Post by: Brahim on August 28, 2016, 01:58:44 PM

Hi

Yes
During the start process. it looks to have negociation Problem.
When on my router I have auto neg or 1000 FD the port of NAS is in 10 or 100.
When I Force in 100 or 10 Falf or full the port of Nas is in 1000.
As per the LED status of the port on the NAS.
I try to change the cable a new straight or cross cable (full croos).
I try also to change with Layer 2 switch.
i clean the connectors.

Idea looks ;issing now.
Anyone can help?
Regards.
Bra

Title: Re: DNS320-LW A2 Update 1-07b04
Post by: feuz on September 01, 2016, 12:39:22 PM

My NAS restart but only with one disk.

The 2 disk are OK, it start with the 1st or the 2nd disk on any of the 2 ports but when i plug the both it don't start ...

Title: Re: DNS320-LW A2 Update 1-07b04
Post by: ivan on September 01, 2016, 01:04:09 PM

Quote

The 2 disk are OK, it start with the 1st or the 2nd disk on any of the 2 ports but when i plug the both it don't start ...

That is usually because the power supply is failing and not supplying enough current so the voltage drops and the NAS can not start.

Check by using another power supply (just make sure it supplies 12 volts and at least 3 Amps - more Amps is no problem).