D-Link Forums
Eagle Pro AI => R15 => Topic started by: FurryNutz on August 24, 2021, 03:33:58 PM
-
Speed test after setup completed:
Modem: NG CAX80 (modem only mode)
1Gb/50Mbps ISP service
Wired PC ethernet connected to R15 router:
(https://i.postimg.cc/15fsnTq2/1st-Speed-Test-Wired-Results-Over900-Mpbs.png) (https://postimages.org/)
R15s onboard speed test. QoS not enabled:
(https://i.postimg.cc/28Mm4wd6/R15-Internal-Speed-Test-Results-Just-Over200-Mpbs.png) (https://postimages.org/)
-
GRC uPnP Exposure Test: Failed
For some reason the test fails to complete or continue when the test is selected to run. Tried two different browsers and it seems to stall at this point.
(https://i.postimg.cc/0Nqs4yB1/u-Pn-PTest-Failed2-Run.png) (https://postimages.org/)
-
GRC ShieldsUP Tests Results: Failed
(https://i.postimg.cc/mrPf5FbD/Sheilds-Up-Failed.png) (https://postimg.cc/kVPpVGR3)
----------------------------------------------------------------------
GRC Port Authority Report created on UTC: 2021-08-22 at 21:14:50
Results from scan of ports: 0-1055
1 Ports Open
1046 Ports Closed
9 Ports Stealth
---------------------
1056 Ports Tested
The port found to be OPEN was: 53
Ports found to be STEALTH were: 21, 80, 135, 136, 137, 138,
139, 443, 445
Other than what is listed above, all ports are CLOSED.
TruStealth: FAILED - NOT all tested ports were STEALTH,
- NO unsolicited packets were received,
- A PING REPLY (ICMP Echo) WAS RECEIVED.
----------------------------------------------------------------------
Firewall Settings on router at time of testing:
(https://i.postimg.cc/XvK9BW1k/Fire-Wall-Settings.png) (https://postimg.cc/mcDPKvsP)
-
GRC DNS Anti-Spoof Test Results: Passed
(https://i.postimg.cc/MGbSJJCM/Anti-Spoof-Test-Results-Passed.png) (https://postimages.org/)
-
Seeing same results with SpeedTest. My ShieldsUp had all ports as stealth. Double check the router's firewall settings as they are all off by default.
-
1st FW update: Failed
I guess users don't have a say if they want to avoid a FW update when the router is set up?
I was not able to cancel this update window so I had to proceed:
(https://i.postimg.cc/L4ymsRnj/1stFWUpdate.png) (https://postimages.org/)\
FW Update Progress window seen:
(https://i.postimg.cc/brv8RVFG/FWUpdateProcess.png) (https://postimages.org/)
FW Update Completed window seen:
(https://i.postimg.cc/rsYTZGvf/FWUpdateSuccessWindow.png) (https://postimages.org/)
After the FW window said it completed I looked over at the router and all lights were OFF accept for the Power which was AMBER. I let it sit like this for a few minutes to ensure the router wasn't doing anything else. It didn't change and never came back to ready. I powered OFF the router for 10 seconds then back ON and luckily the router came to ready.
-
Eagle AI app Setup on Android Pad: Failed
Samsung Galaxy Tab S2 v7.0
I installed the app thru the Google store on this pad and used the QR code on the app to start the install process. I got to the Connecting To your Network screen on the pad and the app stalled here. I left it for few minutes and it would not progress.
(https://i.postimg.cc/LhKcWHHb/Android-Eagle-App-Stall-20210822-135536.png) (https://postimg.cc/1VB7n1VG)
So I had to set up the router using a wired PC and web browser.
-
Furry,
Any luck getting an IPv6 address? or was it your ISP did not offer it
-
Ya, SparkLight doesn't offer native IPv6. Not sure they ever will. :-\
-
Mine at home pulled IPv6 with the latest firmware.
Also experiencing built-in speed test produces slower speeds than my other routers. I will ask about that.
-
;)