Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[mRgANDALF]

Good Morning,

I have a D-Link 320L NAS mounted as a virtual hard drive on a Windows 10 PC and on a laptop with the same operating system. After trying to mount an FTP over the NAS, I created an FTPuser user (there was no user created until then) and from there the NAS virtual drive stopped working on both the PC and the laptop. After investigating a bit, I sensed that Windows 10 did not support this old NAS with users, so I deleted the accounts and it worked again on the laptop (after asking for a setting I do not remember) but not on the PC. Below I show the screens.

This is what the windows explorer recognizes as networked devices.



We see this by clicking on D-Link 91D98D

https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png

https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png]https://k60.kn3.net/2/5/5/5/9/2/710.png

This is the windows message when you want to access Volume_1 on the PC. In the notebook, the content is accessed without having to enter a password.

https://k60.kn3.net/E/F/3/4/C/A/97A.png

The NAS log shows failed [admin] access for the PC and a successful admin login for the laptop.

This is what the tab Properties on the PC shows.

https://k61.kn3.net/E/6/0/9/4/C/7AC.png
https://k60.kn3.net/D/3/6/9/F/D/358.png

And this what it shows in the Portatil (where it works well)

https://k61.kn3.net/E/1/C/1/0/1/E9A.png
https://k60.kn3.net/C/8/E/F/B/1/E59.png

Clicking on change owner shows in both cases the same window.

https://k61.kn3.net/D/A/4/6/E/6/E99.png

I think it must be a permission problem. I do not have the possibility to restore the system to a previous state because it was not configured. Any ideas?

Thank you.

[FurryNutz]

Link>Welcome!

• What Hardware version is your DNS? Look at the sticker behind or under the device.
• Link>What Firmware version is currently loaded? Found on the DNSs web page under status.
• What region are you located?

http://forums.dlink.com/index.php?topic=65722.0
http://windowanswers.com/windows-rt/windows-10-falls-to-access-network-drives-297748.html