• February 23, 2025, 01:09:30 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Best Optimize Setting for gaming experience  (Read 11590 times)

madapaka1323

  • Level 1 Member
  • *
  • Posts: 1
Best Optimize Setting for gaming experience
« on: May 31, 2012, 10:44:31 PM »

Hi, I need help setting my 825 router on the best optimize setting for my ps3, Im running wireless on it and the router is about one room away from my ps3 which isnt that big of a difference since I am getting 95-100% signal on it, the issue is the rate speed runs about 36m-54m it NEVER, or at least I havent seen it go higher than that.

I turned the QO6 engine but it didnt really change a thing, will running this wire do the majic? or is there another alternative set up I can do on the router to have it run on best settings.

I'd appreciate the help, pls. and thank you :)
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Best Optimize Setting for gaming experience
« Reply #1 on: June 01, 2012, 07:04:07 AM »

Welcome!
What Hardware version is your router? Look at sticker under router.
What Firmware version is currently loaded? Found on routers web page under status.
What region are you located?


What ISP Service do you have? Cable or DSL?
What ISP Modem do you have? Stand Alone or built in router?
What ISP Modem make and model do you have?
If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.
To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged.
If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.

Some things to try:
Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
Enable uPnP and Multi-cast Streaming under Advanced/Networking.

Wireless Installation Considerations
What wireless modes are you using? Under Setup/Wireless/Manual.
Try single mode G or mixed G and N on 2.4Ghz and single mode N on 5Ghz?
Channel Width set for Auto 20/40Mhz or try 20Mhz only.
Try setting a manual channel to a open or unused channel.
What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto.
What wireless devices do you have connected?
Any other WiFi routers in the area? Use InSSIDer to find out.

Turn off WISH, and WPS under Advanced.
Turn off Short GI, WLAN Partition,and Extra Wireless Protection if you have it. Under Advanced/Advanced Wireless.

Review the Gamine, Qos and GameFuel stickies in the FAQ Library. Theres one for PS.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.