Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[FurryNutz]

You have a Laptop to test by chance?

Only the wireless is effected?

[JoeKhar]

The surface pro is a laptop/ultrabook tablet of sorts. Intel i5 4gb ram etc

Only the wireless. Gigabit continues to run.

20 minutes in. No changes in speed. Still connected. Still running tests.

[FurryNutz]

How long does it usually take?

[JoeKhar]

15-30 minutes. Going to test a few minutes longer. 40-50.


Hit 30 minutes now.

Do you happen to know the actual differences between 1.02 and 1.01? The channel log doesn't seem that specific.

Menus also happen to load faster. Not that the router was that slow in the first place.

[FurryNutz]

I don't know off the top of my head...

[JoeKhar]

50 minutes in.

You may want to update the notice that 1.02 fixes it. later on, I'll report back in the morning if it is still connected. Which it should be.

I had the other one running still as 1.01 - Disconnected about 18 minutes in. They changed something more than just security settings it seems.

1.01 is seemingly broken for N.

Nearly an hour and nothing disconnected on the router running 1.02

Edit: Note 2 has been connected the entire time as well.

[JoeKhar]

As I said, I'll report back in the morning if anything changes.

Wireless N (only)

Channel 11

WPA 2 - AES

Auto 20/40

1.02 Firmware (1.01 has all the same settings, and it failed)

[FurryNutz]

 

[JoeKhar]

Still connected as of right now. No disconnects during the night being reported by any devices.

1.02 works with the settings.

1.01 does not.

I'll stick with the beta firmware until further notice.

[FurryNutz]

Awesome, keep us posted.

[JDW]

Still connected as of right now. No disconnects during the night being reported by any devices.

1.02 works with the settings.

1.01 does not.

I'll stick with the beta firmware until further notice.

JoeKhar, I'm having the same issues as you are.  I found that 1.02 kept Mode N for a much longer time, maybe even longer than a day, but still eventually failed.  However, I found that rev 1.02, Mode G only, WPA2, AES failed very quickly.  When you are finished testing Mode N, would you mind setting your device to Mode G only to see if your device also shows the same symptoms?

Also, were either you or FurryNutz able to get an IPv6 address from the router?  At rev 1.01, I was able to, but not at rev 1.02.

[FurryNutz]

I'll check to see if I can get an IPv6 address from my v1.02.

Please list your IPv6 router configuration setup details so we can check it out.

[JoeKhar]

JoeKhar, I'm having the same issues as you are.  I found that 1.02 kept Mode N for a much longer time, maybe even longer than a day, but still eventually failed.  However, I found that rev 1.02, Mode G only, WPA2, AES failed very quickly.  When you are finished testing Mode N, would you mind setting your device to Mode G only to see if your device also shows the same symptoms?

Also, were either you or FurryNutz able to get an IPv6 address from the router?  At rev 1.01, I was able to, but not at rev 1.02.

Well, before, that was the only way my devices stayed connected. That was on mode G. Since about 12 central time last night, my devices have stayed connected. Still doing more testing though. I am keeping everybody posted.


I will also test out 1.02 with aes and G. That may be the issue. One step at a time.

[FurryNutz]

Ok, I can confirm that IPv6 addresses are not being handed out to my Mac Book Pro OSX 10.7.5. I tired Local Only connection and enabled Auto Detection on the IPv6 Manual Internet and Enabled the Local LAN options as well, rebooting and watch my network settings to populate. Only IPv4 populated. 

I have sent this to my contact at D-Link for there review. Please be patient while the information is reviewed.

[JoeKhar]

After 24 hours, my devices are still connected. No disconnects at all.

Not saying it is fixed, but a good step in that direction. I'm keeping one router up with the same settings, going to test out g with AES shortly on the other router.

JDW, whenever you can, if you can give me your exact settings you used, that would be helpful. For Mode G with AES (20hz mode etc)

Just to compare.