Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[tuntun]

any work around to use this fw on Europe HW?
Thx

[FurryNutz]

You'll need to phone contact your EU regional D-Link support office and inquired about if they are going to update the EU region.

Thanks.

any work around to use this fw on Europe HW?
Thx

[FurryNutz]

Thought I would post my experiences so far,

Been very good for where the router is actually place back on one side of the house in a corner office room.

Have 2 xboxes, 1 wired and 1 on a 5Ghz DAP-1533 wired AP to the 655. Using XBL Gaming and QoS sticky information, Gaming was great, full green bars in BO2. Only 1 or 2 games were signal was Yellow and probably due to other probable player issues.

Router is behaving well and seems very stable.

Signal is good however on 2.4Ghz my iPhone was not getting great signal however distance and placement of router is playing a role in that. If if move the router back into the living room from opposite from where office is, well, signal wouldn't be an issue.

Over all, v2.11NA is good other wise.

Enjoy everyone.

Thank you D-Link. 

[AlexDrew]

is this FW available to upgrade on DIR-655 B1 2.10NA Canada version?

[FurryNutz]

Yes Sir. 

[fzappa]

I've been holding back (still using 2.03).  This version sounds stable, at least for the few days it's been out.  Will I be able to just upgrade or will it require a complete set up of my settings again?  I always save a config file and would hate to have to do page by page screenshots to recreate each and every setting.

[FurryNutz]

IF your not to concerned about issues with v2.03 or if your router is working well, I recommend keeping what is loaded.

If you do decide to update, just follow the FW update process sticky. I recommend doing a clean install and set up from scratch to be sure. I did this and quite pleased with this version. 

I've been holding back (still using 2.03).  This version sounds stable, at least for the few days it's been out.  Will I be able to just upgrade or will it require a complete set up of my settings again?  I always save a config file and would hate to have to do page by page screenshots to recreate each and every setting.

[sm00thpapa]

Nice to still see support for this router. Has D-Link added the 40 GHz only channel width yet?

[FurryNutz]

It won't be. D-Link sas to follow the good neighbor policy which does not allow for 40Mhz only. No future routers have this either.

[sm00thpapa]

Ok thank you FN for the info.

[nicknml]

This version has also appeared to fix the DNS issues I had (I had to keep flushing my DNS cache.)

[Only520]

UPdated from a 2.03 NA, and when torrenting it totally lags.  Nothing loads, can i flash back  to 2.03 na ?

[FurryNutz]

Link>

Welcome!

• What region are you located?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?
• What ISP Modem service link speeds UP and Down do you have?

Did you follow this for upgrading FW?
 FW Update Process
It's recommneded to do a factory reset, send the FW file, factory reset once more then set up the router from scratch.

Let us know if that helps.

UPdated from a 2.03 NA, and when torrenting it totally lags.  Nothing loads, can i flash back  to 2.03 na ?

[Only520]

I am located in California, Charter Cable is my provider.  30mb down and 4mb up. 

Will try your recommend settings and hopefully that will fix  the problem.

[genreefer]

It appears that 2.11 randomly reboots the router. Multiple times a day I might add.