Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[FurryNutz]

Ok, here it is, lots of goodies:
http://forums.dlink.com/index.php?topic=55510.0

NOTE: I HIGHLY RECOMMEND DOING A FACTORY RESET BEFORE SENDING THE FW FILE, THEN ONE MORE AFTER SENDING THE FW FILE, THEN SET UP THE ROUTER FROM SCRATCH WITH OUT RE-LOADING ANY SAVED CONFIG FILES. Reason being is that there are many new features and changes to the router and loading a previously saved configuration from file could and might cause problems due to the differences in changes. Please set up the router from scratch after loading the new FW and doing one more factory reset.

Let us know how it works for you.

Please post your experiences here and list your fixes here if any, and I'll adjust the Features Request and Bugs thread.

Lets get crackin people.  

Thank you D-Link.

[Lexist2112]

Beat me to it Furry, I have been checkin daily for a new FW and was pleasantly surprised. Looks like a lot of additions to the router. Can hardly wait to get home and upgrade!!!  

    

Release Notes:

Problems Resolved & Enhancements:
1. Fixed: Browser Compatibility for:
    -http://dlinkrouter.local
    -http://192.168.0.1
    -using QRS Mobile
2. Fixed: Formatting in DHCP table
3. Fixed: Updated WLAN Driver for stability
4. Fixed: ACL rule can be deleted
5. Fixed: MAC Filtering can On/Off even if rules exist
6. Fixed: MAC Filtering config requiring reboot
7. Added: Syslog under Status->Logs
8. Added: Dynamic DNS under Advanced->DMZ
9. Added: 5GHz Bursting as Default Enabled
10. Added: WPS-PIN/PBC (for Win8.1 Logo, WPS logo)
11. Added: Auto 20/40Mhz 2.4GHz Co-existence
12. Performance Tuning: LAN-WAN QOS
13. Performance Tuning: 'my network map'
14. Improved: MAC Filtering GUI Table formatting
15. Improved: Inc. to 25 entries/page in Log
16. Improved: Setup wizard bandwidth testing
17. Improved: GUI Layout and Graphics
18. Improved: Factory Default Setup Wizard behavior
19. Improved: Web GUI for setting wireless encryption method
20. Improved: User feedback messages
    - Page return flow when press cancel
    - Add Ok button to 'Warning' messages
    - Prompt saving setting when press cancel
    - Prompt saving when user abandons page
22. Improved: Correct DHCP Reservation Table Labels
23. Improved: Correct DHCP Reservation IP management
24. Improved: Correct DHCP Reservation GUI Button Improvements
25. Remove: "802.11b only" mode in 2.4GHz.
26. Remove: Guest field in wireless status

[FurryNutz]

  Hehe. Ya I checked yesterday too, I missed it by hours...actually a different poster mentioned it this morning.

I haven't seen a FW update release notes this long ever on any D-Link router. LOL. 

We hope it works well...Let us know. 

[Lexist2112]

Hehe. Ya I checked yesterday too, I missed it by hours...actually a different poster mentioned it this morning.

I haven't seen a FW update release notes this long ever on any D-Link router. LOL. 

We hope it works well...Let us know. 

I assume you'll be updating as well???

[FurryNutz]

I was thinking you'd be holding back for the next FW rev and skip this one? Hehe.  

Duh. 

[FurryNutz]

Ok so I got home to day and after I finished working on my bike and was then able to sit down and upgrade the 5500 to v1.10NA. I downloaded the zip file to my Mac Book Pro OSX 10.7.5.

I used Safari and did a factory reset after saving off the config to file.
I then sent the FW file and let it apply.

I noticed that the Mac Book Pro did not reconnect to the router after the FW applied and only got a self assigned address. I though oh boy, router is bricked.

I then power cycled the router and got a valid IP address and got reconnected to the routers web page.

I went ahead and set up the routers WiFi and some IP reservations and Internet DNS and turned OFF DNS Relay.

I reviewed all the web pages for changes and noticed the new features.

I completed my configuration of the router, saved settings and turned it off. I removed my other DIR series router from the main ISP modem and rebooted the ISP modem. During this time frame I installed the 5500 LAN cabling and powered ON the router.

Using my Mac Book Pro and Safari, FF and Opera. I continued to add 2 xbox IP reservations and review the other router web pages. I started to play with the SB options and let the test run manually to see what speeds it could aquire. 29Mb down and 2.25 up was the result for a 50/2 cable service. I set the default setting back to 100/10 and attempted to save settings and reboot. I noticed that I received a message about a warning that my current browser was not HTML5 compatible and that I should use a browser that could use and display HTML5. At one point in navigating the menus, the 500 Internal Server Error was displayed. After that, the routers web page became inaccessible. I'm currently writing this while the web access to the router is not functional however internet is working. I'm having to power cycle the router each time to gain access to the routers web page when the page can't be access . The web page access on the router seems worse after going online with the 5500 using v1.10NA. Safari, FF and Opera are not accessing the routers web page on my Mac Book Pro using a LAN wired connection. Over all, I haven't seen this kind of behavior on any other router or shipping FW.

Going to factory reset the router and clear it all out and just set up SSID and PW, Time and leave everything else default.

Update, after doing a factory reset and setting up basic settings, still saw router web page in-accessible using Windows 7 x64 and Mac Book Pro OSX 10.7.5.

[Lexist2112]

Upgraded the router to FW 1.10b04. Here is my check list:

1) Useing Toshiba Laptop running Win 8 32 bit
2) Downloaded the new FW using Firefox.
3) unzipped FW ontu desktop
4) Usually save Config file...forgot to do it..oh well. Recommend save config file.
5) Hard reset the router, using button underneath router.
6) Connect laptop to router port1, accessed config page and updated FW using Firefox.
7) wait 240min..................
went back in to confirm FW was updated and it was, noticed it only read FW1.10
9) reset within the router software.
10) Manually config ALL settings.
11) router is up and running with current config.

Thus far router is running well and all my config is saved and running. Noticed within FF that the ABE settings is enabled and noticed active download and active upload is missing, but in Safari it is present. I think FF browser cache is just being twonky. Haven't rebooted my Lan machine ....yet.

Active Download Speed :   
100.00 Mbps
Active Upload Speed :   
10.00 Mbps
Status :   
Testing


Furry read your post on your not able access the config page on Safari web browser and having to reboot in order to access config page. I would try a hard reset, button underneath the router and manually set up the router again. If that doesn't do it, are we able to reinstall the latest FW again?

Will run the router thru its paces tomorrow and report back.

PSS- No IP V6 in this update?

[FurryNutz]

Ya I factory reset before and after the update. After experiencing the UI problems I did do another factory reset and then set up SSID, Time and Remote access and SB I set for manual speeds and turned OFF ABE. I left everything else alone. Still not sure what was going on last night. The UI seemed sluggish as well while navigating.

I also notice that if I do anything with SB and save settings and reboot later and try to navigate to a different location, I'm getting a windows that says un-saved settings haven't been applied, OK to continue or cancel.  

I played XBL and BO2 last night with the roomie. Had a good time. Saw a couple of Yellow signal status at the beginning however seem to go green signals after a few games in. Overall gaming was great.

I to also noticed that the status was always "testing"-
Active Download Speed :  
100.00 Mbps
Active Upload Speed :  
10.00 Mbps
Status :  
Testing
Not sure what the behavior is supposed to be now. I presume that over time the status should change. I wonder if there is a time frame we should wait for this to complete. The one time I think it did complete for me it found less than what I get for 50/2. Around 20's on the Down. UP was correct at 2Mb.

I might try a re-load of FW using a Windows PC this time for a 2nd run. Just seemed odd that I had problems that I don't usually see using a Mac.  

Still not Wireless Status page for wireless devices that are connected. 

[ASTRO_Henry]

Upgraded the firmware to V1.10 but I have YET to test it on gaming on Xbox 360. Didn't noticed anything on the improvements towards the GUI or interface. I noticed that on the Device Info page shows FIRMWARE Version:  1.10 , 27, Aug, 2013 while the firmware was just released on on 9/4/2013. I've tried soft and hard reboot; still hows that version and date.

[FurryNutz]

The date is correct. Shows same here. Date will be different from actual dates they get posted to the web. 

[ASTRO_Henry]

Gotcha. Nice to know. Learned something new today. Probably has to do with the process to certify before releasing to the public.  

[FurryNutz]

So I went back to today and factory reset the 5500, uploaded the v1.10 FW again using IE 10 in Windows 7x32 and factory reset once again after the install. I used the set up wizard to set up that and the WiFi. Let it reboot. I then began to custom set up my setting like I did before using my Mac. Set up custom DNS, turned OFF DNS Relay. Setup some IP reservations for devices being seeing by the router. Set up Remote Management and Time. I rebooted again to save all the settings and get them applied. I noticed that i made a mistake on one of the DNS addresses I input so I corrected that and rebooted once again. After this, the UI was not accessible again.  I tried from a different Windows 7x64 PC and could not access it. I power cycled the router and apparently I didn't leave it off long enough, still would not access the routers web page after 2 more power cycles. I also saw the 500 Internal Server Error message on one occasion when attempting to access the routers page in IE. However I did have internet access. I looked and thought, I wonder if my 250Gb USB drive connected to the router could be an issue. So I unplugged it and rebooted the router. Finally got access. I continued to reserve more IP addresses and review the various pages navigating in and out of them.

I notice that Filter is also displaying a Un-Saved Configurations message when navigating away from that option, even when I didn't change anything.

Also during the setup wizard setting up SB and it doing it's speed test, its only getting 7Mb down and 2Mb on the up. I confirmed this by running a wired LAN speedtest.net on my Mac:


I then disabled ABE and input 100.00/10.00, saved settings and rebooted then restested speedtest.net:

Seems that SB and ABE is not correctly getting accurate speeds results. So ABE is disabled again for me.

I'm curious if anyone has a USB drive connected to the 5500 and Media Server enabled and has seen any router web page crashing, not accessbile or 500 Internet Server Error experiences? Please let us know. I hope I'm not the only one. I'll try a different USB drive as well.

[Lexist2112]

Furry posted my speed results in that secton with and without ABE, my ping was DEFINITELY better when ABE is OFF

http://forums.dlink.com/index.php?topic=55013.15

[jgraffeo]

So I pulled out my DGL-5500 earlier today and put back my DIR-857.  The DIR-857 works a lot better for me regarding speed and wireless strength/performance.  Not sure why.  I have the settings the same way.  I then saw your post and decided to give the DGL-5500 a shot with the new firmware.  I followed your steps of resetting the router, applying the new FW, reapplying all the settings manually, rebooting, etc.

I have IE10 in Windows7x64.  I didn't have any issues with my browser as Fuzzy described.  I do not have a HDD connected. 

In all honesty, I am still having the performance issues on my Wireless using the DGL-5500.  It is almost unusable on my 2.4Ghz band (I have 100MB/20MB service but speedtest was showing <1MB/1MB on wireless 2.4GHz).  The 5Ghz band seems to be ok but still no where getting my LAN speeds.  I also did not get accurate measurements using their speed test in the SB page.  I tried with ABE on and without.  It is better without when using SB for me.  Not any different from old FW unfortunately.

I am not sure why this router's performance is so bad for me compared to the DIR-857.  I really like the idea of SB on the DGL-5500.  I was hoping the new FW 1.10 would have fixed some of these performance issues, but it doesn't seem to have really addressed any of that stuff. 

[Lexist2112]

Another report in regards to the XBOX 360. I have it connected to the 2.4ghz , ABE off and have been gaming using GOW Judgement. Game play was great no lag what so ever. It played possibly better with ABE off and was just the same with FW 1.01.

Rest of my wireless clients have been good since I turned ABE off. Don't know why ABE interfers with band with speed, just can't figure it out...whatever, works great when its off.

Just wish they could have increased the output on the 5ghz range, would have been nice.

Still happy with the performance overall of this router