Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[FurryNutz]

NO, most of the WPA2 Crack issues are with the actual Client HW devices them selves, like phones and wireless repeaters and access points or USB wireless adapters.

Check with any of your client side HW Mfrs for updates regarding this issue.

Modem: DLink DIR-890L
Version: HW: A1 FW: 1.20
Win 10 Pro update Build 15063.764 Version 1703

Region: Brazil


Hello.

Due to these problems with the security of the wifi some update patch ??
Recently I got updates from FW 1.10, 1.11 and 1.20. But this last update I can not keep my new information in QOS.

It's not saving I'm using google browser tks.

[samukets]

Modem: DLink DIR-890L
Version: HW: A1 FW: 1.20
Win 10 Pro update Build 15063.764 Version 1703

Region: Brazil


Hello.

Due to these problems with the security of the wifi some update patch ??
Recently I got updates from FW 1.10, 1.11 and 1.20. But this last update I can not keep my new information in QOS.

It's not saving I'm using google browser tks.

Hi friend, turn off the router, wait 10 seconds and for firefox config the QOS, it only accepts configuration in the first few seconds after being connected, then for some reason it no longer accepts. Greetings from Salvador-Bahia.

Oi amigo, desligue o roteador, espere 10 segundos e pelo firefox configure o QOS, ele só aceita configuração nos primeiros segundos após ser ligado, depois por algum motivo ele não aceita mais. Saudações de Salvador-Bahia.

[FurryNutz]

So turning off the router then back on you can configure QoS?

Did you try a factory reset then use FF or IE11 to configure QOS?

Modem: DLink DIR-890L
Version: HW: A1 FW: 1.20
Win 10 Pro update Build 15063.764 Version 1703

Region: Brazil


Hello.

Due to these problems with the security of the wifi some update patch ??
Recently I got updates from FW 1.10, 1.11 and 1.20. But this last update I can not keep my new information in QOS.

It's not saving I'm using google browser tks.

Hi friend, turn off the router, wait 10 seconds and for firefox config the QOS, it only accepts configuration in the first few seconds after being connected, then for some reason it no longer accepts. Greetings from Salvador-Bahia.

Oi amigo, desligue o roteador, espere 10 segundos e pelo firefox configure o QOS, ele só aceita configuração nos primeiros segundos após ser ligado, depois por algum motivo ele não aceita mais. Saudações de Salvador-Bahia.

[samukets]

Can i change ppoe mtu auto to 1500? My mtu manual option dont accept any value, always return to auto...

[FurryNutz]

Yes you should be able to set MTU values. Are you using a PPPoE ISP service and have the PPPoE selected instead of Dynamic?

[samukets]

Yes, router mode, pppoe, but if a change mtu always return to auto.
set mtu to manual, 1492 and after 60secs reboot nothing, auto again.
Other thing, 1492 is the maximum router mtu in ipv4.
IPV6 accept normal mtu set to 1500 or other value.

[FurryNutz]

I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this. We find that phone contact has better immediate results over using email.
Let us know how it goes please.

Yes, router mode, pppoe, but if a change mtu always return to auto.
set mtu to manual, 1492 and after 60secs reboot nothing, auto again.
Other thing, 1492 is the maximum router mtu in ipv4.
IPV6 accept normal mtu set to 1500 or other value.

[samukets]

I appreciate the help but the local support from Brazil only serves as a guide for downgrade and firmware upgrade, I have never been able to have a productive conversation with them.

Thank God that there is this forum to exchange experiences, it was my salvation.

[FurryNutz]

I would let them know since they will need to review and correct this issue if they deem it reproducible on there end. If a prior version works and v1.20 doesn't, I presume it should be easy for them to correct...

[samukets]

To be honest, since the first firmwares I have never been able to set pppoe mtu manual.

[FurryNutz]

Ok, I'll have my region check on this here. However I recommend that you contact your regional office and ask for escalated support and notify them of this issue.
Each region seems to do there own thing when it comes to FW development and support.

[CoDeCX999]

Hello.

Well I was able to make a new configuration using FF Nightly and had good success in configuring zero on the Dir-890L.

Today I had a new update on win 10 version fall creators
Build: 16299.19 V. 1709
I noticed that I have performed well on my machine, as for my connection.

But I still realize that the version of FW 1.10 is more stable than 1.20 in relation to QOS and MTU configurations.

Thank you for supporting the support emails I sent and I have had great answers in Brazil. And help support here in the forum.

TKS. 

[FurryNutz]

Thanks for your feed back and information. I'll be sure to have D-Link look at the QoS UI saving issue again and the MTU saving issue as well here for this region.

[samukets]

Can anyone give me a technical explanation of how Smart Connection worked well in the previous firmware and in that other one already loses speed in some devices? Very strange, I had to disable the SC to have stability again

[FurryNutz]

I haven't noticed anything on mine in this regard. Been working well, however mines in a AP mode configuration and not as main host router.

Was a factory reset performed before and after loading this version and set up from scratch.

Can anyone give me a technical explanation of how Smart Connection worked well in the previous firmware and in that other one already loses speed in some devices? Very strange, I had to disable the SC to have stability again