• October 31, 2024, 04:41:23 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: default login for DCS-942L not working  (Read 6972 times)

mhz

  • Level 1 Member
  • *
  • Posts: 3
default login for DCS-942L not working
« on: July 25, 2018, 07:42:49 PM »

I recently pulled out an old DCS-942L to user again after it has been sitting in a drawer for a while.
I reset it back to factory using the pin hole on the back and waited for it to obtain an ip address.
I found the IP by doing an ip scan on my network and then attempted to login to it.
For some reason it will not accept the default username of admin and no password as per the manual.
I cannot login to the camera at all. Any help would be appreciated.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: default login for DCS-942L not working
« Reply #1 on: July 26, 2018, 06:58:52 AM »

Link>Welcome!

  • What Hardware version is your DCS? Look at the sticker behind or under the camera.
  • Link>What Firmware version is currently loaded? Found on the DCSs web page under status.
  • What region are you located?

What Mfr and model is the main host router?

What browser are you using? Try IE11 or FF browsers.
Be sure to clear browser caches before accessing the cameras web page.
Set up the camera first using the installation software for it found on D-Links support page...
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

mhz

  • Level 1 Member
  • *
  • Posts: 3
Re: default login for DCS-942L not working
« Reply #2 on: July 29, 2018, 09:32:32 PM »

Hardware version A3
Firmware Version 1.11
Not sure what version if currently loaded as I can't login to it
I am located in Australia
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: default login for DCS-942L not working
« Reply #3 on: July 30, 2018, 06:41:29 AM »

Let us know if the set up software works...
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

mhz

  • Level 1 Member
  • *
  • Posts: 3
Re: default login for DCS-942L not working
« Reply #4 on: July 30, 2018, 06:32:21 PM »

Nope, the software seems pretty flaky on Windows 10 and even when I get it to work it doesn't even detect the camera
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: default login for DCS-942L not working
« Reply #5 on: August 14, 2018, 07:00:35 AM »

I presume the camera maybe bad now.  ???
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.