D-Link Forums
The Graveyard - Products No Longer Supported => D-Link Storage => DNS-323 => Topic started by: dicrouthamel on August 09, 2009, 05:21:37 AM
-
Just wondering what would be the fastest way to replace the 500 GB hard drives with 1.5 TB hard drives and copy the data over. I'm guessing I could take the 500 GB drives out, read them in Windows 7 (it can read EXT2, right), and copy the data over to the 1.5 TB drives?
thanks!
-
that's what i would do. although i would place 2TB drives instead (1.8 FW i believe allows this) so i would not have to replace the drives in a loooooong while.
-
Standard or RAID1 configuration?
-
Standard or RAID1 configuration?
Standard configuration - no raid :)
-
If you have two 1.5TB drives I would take on of the drives out and replace it with 1 of the 1.5TB drives power it back up and move the data from the remaining 500GB drive to the 1.5TB. Next Power it down and swap the 500GB drive with the other then power it up and do the same. Once done remove the 500GB and insert the second 1.5TB and format it.
-
I would like to do the same thing and have two 500GB drives in a RAID1 config and would like to move to either a pair of 1.5 or 2TB drives also in a RAID1 config. I think I am running fw1.07 (although I am not at home to check it).
I have space on the network to move the data if it makes sense but if there is someway to do one drive at a time that would be better for me.
1. I am looking for a methodology to accomplish this upgrade
2. Does the config remain in the device in NVRAM even if both drives are lost?
-
Thought I would bump this one, as I am looking to buy new drives this weekend and looking for a strategy to upgrade to the old 500GB drives. Thanks in advance.
-
The easiest way will be to backup the data, install new disks, create a new array and restore. There is no simple way to swap one disk at a time and "grow" the array.
-
The easiest way will be to backup the data, install new disks, create a new array and restore. There is no simple way to swap one disk at a time and "grow" the array.
Thanks for the quick reply. Do you know if the config of the NAS would be preserved? Is the config stored on NVRAM in the unit (not on the RAID set) correct? Thanks again in advance.
-
Usernames, passwords, access, etc. is stored in flash memory and not on the disks - this may or may not be of significance if you "upgrade" the drives - since you will need to recreate the directory structure exactly the same way it was before for the permissions to work.
-
If you have two 1.5TB drives I would take on of the drives out and replace it with 1 of the 1.5TB drives power it back up and move the data from the remaining 500GB drive to the 1.5TB. Next Power it down and swap the 500GB drive with the other then power it up and do the same. Once done remove the 500GB and insert the second 1.5TB and format it.
Can you clarify this for me? I have two 500GB drives in a RAID 1 configuration. Are you saying I should:
1. Power down
2. Remove one 500GB drive
3. Insert new 1.5TB drive
4. ??? If it's a RAID 1, will it automatically mirror the contents? If this so, then:
5. Remove second 500GB drive
6. Insert second 1.5TB drive and the DNS-323 will sync with the first drive.
Is this correct? If not, what is the procedure for a RAID 1 configuration to replace the drive set with a larger one?
Thanks!
-
good question i would like to know as well
-
Is this correct? If not, what is the procedure for a RAID 1 configuration to replace the drive set with a larger one?
Thanks!
No it's not,that is for standard volumes (NO RAID) only - the procedure for RAID was provided in an earlier response. There are other ways, this one is the easiest.
The easiest way will be to backup the data, install new disks, create a new array and restore. There is no simple way to swap one disk at a time and "grow" the array.
-
No it's not,that is for standard volumes (NO RAID) only - the procedure for RAID was provided in an earlier response. There are other ways, this one is the easiest.
Just out of interest, what is it that stops this approach from working? I always assumed when I want to upgrade I'd insert the new disks one at a time and have the array restored automatically. If a disk goes bad you can just insert a fresh one and have the raid array restored, right? So is it the fact the disk is larger that stops this approach from working?
-
If you have a disk fail and you replace it with a larger disk, the system will create the exact size partition used in the original array on the new disk, and the remaining space will be unavailable until you reformat the disks or get creative with linux.
The same thing will happen if you swap the disks one by one and allow a rebuild - you will end up with a RAID array of the original size and have no access to the remaining space on the two disks.
-
If you have a disk fail and you replace it with a larger disk, the system will create the exact size partition used in the original array on the new disk, and the remaining space will be unavailable until you reformat the disks or get creative with linux.
The same thing will happen if you swap the disks one by one and allow a rebuild - you will end up with a RAID array of the original size and have no access to the remaining space on the two disks.
Ahh, I see. That makes sense. Thanks for clarifying that :)
-
No it's not,that is for standard volumes (NO RAID) only - the procedure for RAID was provided in an earlier response. There are other ways, this one is the easiest.
Thanks for the response, but sorry I'm still a bit confused. Unless you're referring to a previous thread, it seems as though none of the previous posters had a RAID 1 setup (but one wanted to move to one.)
Here's what I've intuited so far: If I simply remove one of my 500GB drives, stick it in a PC and copy the contents over to each of the two new 1.5TB drives, I can remove the other 500GB drive and insert both new 1.5TB drives.
If this is correct, great - it shouldn't be a problem. But doesn't the 323 need to format the volumes first?
Again, thanks for the help.
-
jswayze...
You quoted ECF's post and asked if the procedure was "correct" for RAID1 - and I responded in the negative, that procedure will only work for standard volumes - the procedure you outlined, which is essentially a slightly modified version of ECF's post will NOT work, for reasons that I have already covered.
The "new" procedure that you have "intuited" will also NOT work for RAID1 - I have already provided the "easest" way to upgrade a RAID1 array to larger disks.
-
I did a similar upgrade, I replaced two 500gig disks with two 1.5TB disks. I could see no way except to copy all the data back after the disk upgrade. In my case, I have a DNS-323 and a DNS-321, both with 1.5TB drives in RAID-1. I copied all the data to the second box (it was new and empty), installed the larger disks, and copied it back. There didn't seem to be any shortcut.
It take a long time to copy 800gb of data. :D