D-Link Forums
The Graveyard - Products No Longer Supported => DIR-655 => Routers / COVR => Beta Code! => Topic started by: davevt31 on November 11, 2009, 02:12:17 PM
-
Have installed this Beta. Restored saved configuration file and renebled DNS Relay. So far no issues.
-
Does it include SecureSpot?
-
The securespot option is available in this firmware.
-
New shareport version needed, like the previous beta?
-
Unable to restore configuration from file after upgrade.
-
I was seeing the DNS Relay problem in the released 1.32NA. I've installed Build 09, have DNS Relay switched on, and will report back after a few days! Usually it hung within 3 days.
Thanks D-Link for working on this!
-
Only thing I have noticed so far is that when in the admin pages of the router, the advanced section is slow to fill in all the boxes on the side.
-
Only thing I have noticed so far is that when in the admin pages of the router, the advanced section is slow to fill in all the boxes on the side.
What browser is this?
Loads fine on my system using IE8.
-
IE8 on a Win7 machine. It loads there is just a delay for the left side categories to appear.
-
@davevt31: Do you have any antivirus or security solution?
-
Trend Micro.
Its only the Advanced Page. The Setup, Tools, and Status ones are fine.
-
I have zero experience with trend micro but when I use Kaspersky (current version sucks on Windows 7 under heavy network traffic), its NDIS filter slows down Advanced page loading too. It depends on the firmware version and the AV both as far as I have tested. Another user on this forum has the same exp with NOD32 so you might want to check that.
-
Well so far this firmware is running great! (though I'll probably jinx it now)
DNS Relay finally seems to work, and as usual I did not reload my previous configuration, rather I restored the defaults and then set it all up manually. SecureSpot downloaded my port forwarding stuff though once my Internet connection was up. I haven't bothered trying to disable SecureSpot and change my port forwarding though and to see if it saves properly. Also I don't and have never used Shareport.
I'm sitting at 1 day, 7 hours up time. I don't think it ever lasted that long with DNS Relay on before.
-
I have zero experience with trend micro but when I use Kaspersky (current version sucks on Windows 7 under heavy network traffic), its NDIS filter slows down Advanced page loading too. It depends on the firmware version and the AV both as far as I have tested. Another user on this forum has the same exp with NOD32 so you might want to check that.
It seems to be something with my IE and its add-ons slowing things down. I opened IE with no add-ons and the Advanced pages filled in much quicker.
-
Port Forward page is not work
Any thing such as IP address and port filled in will be disappeared after manual reboot.
It happens no matter whether the Securespot is disabled. It happens randomly.
I did not load any *.gws file.
Hardware version is A2
-
I'm not seeing this. I have four ports forward and rebooted several times during initial setup. The forwards are working.
You're saying that after you do a "Save Settings", then reboot, the port forward information randomly disappears? Perhaps you're using UPnP on the same port forwards?
-
I'm not seeing this. I have four ports forward and rebooted several times during initial setup. The forwards are working.
You're saying that after you do a "Save Settings", then reboot, the port forward information randomly disappears? Perhaps you're using UPnP on the same port forwards?
i didn't enable any uPNP setting on any desktop.
-
I'm sitting at 1 day, 7 hours up time.
6 days, 7 hours now ;D
Props to D-Link, this firmware seems to have fixed my major issues.
For those with port forwarding issues, make sure you leave SecureSpot enabled. At least until you have all your settings done and saved. Then you can disable it and they should stay indefinitely.
-
More than a week with 1.32NA Build 09, DNS Relay enabled, no hangups! This is working very well for me!
I was seeing the DNS Relay problem in the released 1.32NA. I've installed Build 09, have DNS Relay switched on, and will report back after a few days! Usually it hung within 3 days.
Thanks D-Link for working on this!
-
No dice for me. Unless I have DNS Relay disabled, I have to to do a soft cycle of my connection to get anything other than IRC working properly again (usually 1-2 days).
-
6 days, 7 hours now ;D
Props to D-Link, this firmware seems to have fixed my major issues.
For those with port forwarding issues, make sure you leave SecureSpot enabled. At least until you have all your settings done and saved. Then you can disable it and they should stay indefinitely.
i can ensure that i did the steps as you wrote
-
i can ensure that i did the steps as you wrote
This problem disappeared after I pressed & held the reset button on the rear panel instead of clicking the web UI soft one. Also, I turned off the whole QoS page(traffic shaping).