• October 29, 2025, 07:37:40 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Pages: 1 [2]

Author Topic: Beta Firmware 1.32NA Build 09 Feedback  (Read 27937 times)

bananaman

  • Level 2 Member
  • **
  • Posts: 55
Re: Beta Firmware 1.32NA Build 09 Feedback
« Reply #15 on: November 15, 2009, 04:11:48 AM »
I'm not seeing this. I have four ports forward and rebooted several times during initial setup. The forwards are working.

You're saying that after you do a "Save Settings", then reboot, the port forward information randomly disappears? Perhaps you're using UPnP on the same port forwards?
Logged

pbodq

  • Level 2 Member
  • **
  • Posts: 31
Re: Beta Firmware 1.32NA Build 09 Feedback
« Reply #16 on: November 15, 2009, 08:38:29 PM »
Quote from: bananaman on November 15, 2009, 04:11:48 AM
I'm not seeing this. I have four ports forward and rebooted several times during initial setup. The forwards are working.

You're saying that after you do a "Save Settings", then reboot, the port forward information randomly disappears? Perhaps you're using UPnP on the same port forwards?

i didn't enable any uPNP setting on any desktop.

Logged

jdrom

  • Level 2 Member
  • **
  • Posts: 43
Re: Beta Firmware 1.32NA Build 09 Feedback
« Reply #17 on: November 18, 2009, 08:11:52 PM »
Quote from: jdrom on November 13, 2009, 07:57:05 PM
I'm sitting at 1 day, 7 hours up time.
6 days, 7 hours now  ;D

Props to D-Link, this firmware seems to have fixed my major issues.

For those with port forwarding issues, make sure you leave SecureSpot enabled. At least until you have all your settings done and saved. Then you can disable it and they should stay indefinitely.
Logged
DIR-655 A4 | 1.32NA Build03

bananaman

  • Level 2 Member
  • **
  • Posts: 55
Re: Beta Firmware 1.32NA Build 09 Feedback
« Reply #18 on: November 20, 2009, 02:42:08 AM »
More than a week with 1.32NA Build 09, DNS Relay enabled, no hangups! This is working very well for me!
Quote from: bananaman on November 12, 2009, 05:06:32 PM
I was seeing the DNS Relay problem in the released 1.32NA. I've installed Build 09, have DNS Relay switched on, and will report back after a few days! Usually it hung within 3 days.

Thanks D-Link for working on this!
Logged

temo

  • Level 1 Member
  • *
  • Posts: 2
Re: Beta Firmware 1.32NA Build 09 Feedback
« Reply #19 on: November 25, 2009, 03:05:08 AM »
No dice for me. Unless I have DNS Relay disabled, I have to to do a soft cycle of my connection to get anything other than IRC working properly again (usually 1-2 days).
Logged

pbodq

  • Level 2 Member
  • **
  • Posts: 31
Re: Beta Firmware 1.32NA Build 09 Feedback
« Reply #20 on: November 26, 2009, 11:36:59 PM »
Quote from: jdrom on November 18, 2009, 08:11:52 PM
6 days, 7 hours now  ;D

Props to D-Link, this firmware seems to have fixed my major issues.

For those with port forwarding issues, make sure you leave SecureSpot enabled. At least until you have all your settings done and saved. Then you can disable it and they should stay indefinitely.

i can ensure that i did the steps as you wrote
Logged

pbodq

  • Level 2 Member
  • **
  • Posts: 31
Re: Beta Firmware 1.32NA Build 09 Feedback
« Reply #21 on: December 13, 2009, 12:21:54 AM »
Quote from: pbodq on November 26, 2009, 11:36:59 PM
i can ensure that i did the steps as you wrote

This problem disappeared after I pressed & held the reset button on the rear panel instead of clicking the web UI soft one. Also, I turned off the whole QoS page(traffic shaping).
Logged
Pages: 1 [2]
« previous next »