• April 20, 2025, 01:23:53 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: DIR-655 Access Control Input  (Read 7312 times)

richard9907

  • Guest
DIR-655 Access Control Input
« on: September 25, 2008, 06:45:04 AM »
I have upgraded my firmware to 1.21.  I need Access control to manage my network.

When I try to enter 11:00 pm to 5:00 AM I get an invalid time error.  This used to work on the old firmware.

Is it just me or is this a problem with the firmware?
Logged

davevt31

  • Level 9 Member
  • ****
  • Posts: 1601
Re: DIR-655 Access Control Input
« Reply #1 on: September 25, 2008, 08:20:29 AM »
The scheduler has issues wrapping around Midnight.  Make a rule from 11:00 PM - 12:00 AM and then another one from 12:00 AM to 5:00 AM and see if that works for you
Logged

EddieZ

  • Level 10 Member
  • *****
  • Posts: 2494
Re: DIR-655 Access Control Input
« Reply #2 on: September 25, 2008, 03:13:32 PM »
This is a generic problem. All my routers through time (Tornado, Asus) have had this problem with 00:00.
Logged
DIR-655 H/W: A2 FW: 1.33

richard9907

  • Guest
Re: DIR-655 Access Control Input
« Reply #3 on: September 28, 2008, 05:50:31 AM »
Well Eddie

The probelm is worse than I thought.  Try entering any start time between 1 am and 3 am and you get an error.  This range is exactly the range of time I need to block.

In addition there are errors in the select machine phase of the wizard.  At times it will not recognise that you have entered a machine.

Bottom line this needs fixing.  It is inoperable the way it is.
Logged

lotacus

  • Level 4 Member
  • ****
  • Posts: 450
Re: DIR-655 Access Control Input
« Reply #4 on: September 28, 2008, 08:21:05 AM »
report this in the beta code thread
Logged

Sammydad1

  • Level 5 Member
  • *****
  • Posts: 722
Re: DIR-655 Access Control Input
« Reply #5 on: September 28, 2008, 11:04:33 PM »
Hi,

This issue is related to some of the others....I was using the 1.11MSBeta and was fine...then when I initially tried to update to 1.20 when it first came out...my access controls were snafu'd...but when I back dated to the MS1.11Beta again, they were fine...  I posted a thread about thiscouple months back, altho the time issue was minor because the Access controls were messed.

I did see the Invalid Time error when I went to modify a control that wrapped around midnite... I had to break it up as suggested...but I went with  10:00 pm to 11:59 pm   for schedule1  then 12:01 am to 10:30 am for schedule2.  I had to create 2 access controls; one for each schedule referenced.

when I updated last week to 1.2105 Beta, they seemed to be fine....
Logged
DIR-655 A2, FW: 1.35NA

EddieZ

  • Level 10 Member
  • *****
  • Posts: 2494
Re: DIR-655 Access Control Input
« Reply #6 on: September 29, 2008, 09:32:32 AM »
Quote from: richard9907 on September 28, 2008, 05:50:31 AM
Well Eddie

The probelm is worse than I thought.  Try entering any start time between 1 am and 3 am and you get an error.  This range is exactly the range of time I need to block.

In addition there are errors in the select machine phase of the wizard.  At times it will not recognise that you have entered a machine.

Bottom line this needs fixing.  It is inoperable the way it is.

You're absolutely right. Should not be too hard to fix since PM does work.
Logged
DIR-655 H/W: A2 FW: 1.33

Lycan

  • Administrator
  • Level 15 Member
  • *
  • Posts: 5335
Re: DIR-655 Access Control Input
« Reply #7 on: September 30, 2008, 09:36:12 AM »
We're aware of the clock issue. I've reported it to PM to see if it can be corrected in the latest firmware.
Logged