Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[woozabi10]

I upgraded then downgraded from 2.00 to 2.03 back down to 2.00, and whenever I'm doing about 600kB/s+ it resets itself. Drops connection drops wireless, wired, and the globe internet icon goes Lambert/orange. I've reset the router to default and it still does that. What could be the cause?

I've done a lot of changing around, disabling unicast, changing from WPA Auto to WPA2, etc etc, I just changed the router to Netgear WGR614 v7 and it works perfectly fine now. I just wish it had N

[FurryNutz]

try changing the WiFi from from mixed to single mode G or N?

[woozabi10]

Didn't help

[FurryNutz]

What security mode are you using? WEP, WPA or WPA2? Preferred is WPA-Personal. WPA2/Auto TPIK and AES.
What wireless devices do you have connected?
Any cordless house phones?
Any other WiFi routers in the area?

[woozabi10]

DHCP
Advanced DNS Service enabled
Use Unicast Enabled
MTU 1500
Mixed B G N
Channel 8
20 MHz
Invisible
WPA Auto
TKIP and AES
DHCP Lease time 1440
Always broadcast
QoS off
SPI Off

iPhone, laptops, cordless phone but that's using VoIP service but the phone itself may or may not be interfering. Like I said, only happens when YouTube videos are streamed 720P+, and other downloading apps like when I tried to update Batman Arkham City.

WiFi in the area, but the channel shouldn't be interfering.

[FurryNutz]

What browser are you using? Try a different browser like Opera or FF.

What ISP Service do you have? Cable or DSL?
What ISP Modem do you have? Stand Alone or built in router?
What ISP Modem make and model do you have?
If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems.

Ensure DNS IP addresses are being filled in under Setup/Internet/Manual?
Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
Turn on DNS Relay under Setup/Networking.
Setup DHCP reserved IP addresses for all devices on the router.
Ensure devices are set to auto obtain an IP address.
Set Firewall settings to Endpoint Independent for TCP and UDP.

What wireless modes are you using?
Try single mode G or N or mixed G and N?
What security mode are you using? WEP, WPA or WPA2? Preferred is WPA-Personal. WPA2/Auto TPIK and AES.
Turn OFF Short GI under Advanced Wireless.

[woozabi10]

Chrome, tried FF, same effect. DSL. Modem is Sagecom 4300. Bridged Modem to router, modem is just a modem with no router features. I also just switched back to my Netgear WRG614 v7 and it works fine. Used Mixed BGN, tried singling them, no good. I was using WPA2/AUTO TPIK and AES. I will now try turnning off short GI, but that's a wireless function, this is wireless and WIRED so not sure if that will make a difference, and will turn off Advanced DNS. The DNS are being filled out.

[Hard Harry]

Not that it really matters (since you said you bridged it) but the 4300 isn't a stand alone modem. Atleast not according to this. I see DHCP, NAT, Firewall, UPnP..all kinds of things a standard modem would have. Just FYI.

[woozabi10]

Seems like a router issue. Swapped out with a new one, no difference. Switched to a Netgear WGR614 v7 and it works fine. No cut outs.

[FurryNutz]

Maybe someone can review your router settings with you using teamviewer.

[slpip]

The router reset when the channel or the n/g/b mode changed.  Channel 8 is similar to channel 6 used by phone or similar electronic devices.  You should use channel 1 or channel 11.  The MTU value should use default 1492.  The channel width should use auto 20/40 Mhz.  DIR-655 is very sensitive to these settings.

[mark3stan529]

if the Internet light or the globe light going to amber..it means both wired and wireless connection is getting intermittent Internet connection..am i right??

Try to set the WAN port speed to 10 Mbps
Try to observe the connection behind the modem to check the if the modem is giving stable Internet connection

[woozabi10]

modem gives perfect connection. I switched to my old net gear and havent had any problems with it. i did try channel 11 and MTU 1492, doing good, so far... MTU 1492 didnt help any, switched to 10mbps, will update.

[FurryNutz]

Let us know, send a PM and we can review the router settings with you via teamviewer.

Are there any log entries when the routers resets during this time frame?

[woozabi10]

Nov 24 20:58:05 debug     gpio create pidfile /var/run/gpio_wan_green.pid
Nov 24 20:58:00 info     [ 2364.990000] module arch cleanup nf_conntrack_ftp: OCM instruction memory free  of 0 @00000000
Nov 24 20:58:00 info     [ 2364.830000] module arch cleanup nf_nat_ftp: OCM instruction memory free  of 0 @00000000
Nov 24 20:57:55 debug     open bandwidth_tmp.txt fail
Nov 24 20:57:55 debug     No DHCP ACK with option DHCP_STATIC_ROUTE
Nov 24 20:57:55 info     Lease of 69.x.x.x obtained, lease time 86400
Nov 24 20:57:55 debug     Sending select for 69.x.x.x...
Nov 24 20:57:55 debug     DHCPC get gateway = 69.x.x.x 
Nov 24 20:57:54 debug     Performing a DHCPC renew
Nov 24 20:57:54 debug     DHCPC Received SIGUSR1='DHCPC Renew
Nov 24 20:57:46 debug     Entering released state
Nov 24 20:57:46 info     DHCP Release WAN IP address = 0.0.0.0
Nov 24 20:57:46 info     Unicasting a release of 69.x.x.x to 67.x.x.x 
Nov 24 20:57:46 debug     Performing a DHCPC release
Nov 24 20:55:56 info     UDHCPD Inform: add_lease 192.168.0.103
Nov 24 20:51:00 info     UDHCPD Inform: add_lease 192.168.0.103
Nov 24 20:48:42 debug     UDHCPD sending ACK to 192.168.0.106
Nov 24 20:48:41 info     UDHCPD sending OFFER of 192.168.0.106
Nov 24 20:48:41 debug     UDHCPD sendOffer : client is in lease/offered table
Nov 24 20:48:41 info     UDHCPD sendOffer : device_lan_ip=192.168.0.1 , device_lan_subnet_mask=255.255.255.0
Nov 24 20:48:41 info     UDHCPD sending OFFER of 192.168.0.106
Nov 24 20:48:39 debug     UDHCPD sendOffer : find a free IP
Nov 24 20:46:00 info     UDHCPD Inform: add_lease 192.168.0.103
Nov 24 20:45:56 debug     UDHCPD sending ACK to 192.168.0.103
Nov 24 20:45:56 info     UDHCPD sending OFFER of 192.168.0.103
Nov 24 20:45:54 debug     UDHCPD sendOffer : find a free IP
Nov 24 20:44:41 info     [ 1565.730000] module arch cleanup nf_conntrack_ftp: OCM instruction memory free  of 0 @00000000
Nov 24 20:44:41 info     [ 1565.580000] module arch cleanup nf_nat_ftp: OCM instruction memory free  of 0 @00000000
Nov 24 20:44:38 debug     [ 1563.430000] jcp_command_register: new command registered EXEC SCANNER DISCONNECT
Nov 24 20:44:38 debug     [ 1563.430000] jcp_command_register: new command registered EXEC SCANNER CONNECT
Nov 24 20:44:38 debug     [ 1563.430000] jcp_command_register: new command registered GET USB_DEVICE_LIST
Nov 24 20:44:38 debug     [ 1563.430000] jcp_command_register: new command registered GET SCANNER_STATUS
Nov 24 20:44:38 debug     [ 1563.430000] jcp_command_register: new command registered GET SCANNER PORT_NAME
Nov 24 20:44:38 debug     [ 1563.430000] jcp_command_register: new command registered GET USB_PORT_NAME
Nov 24 20:44:38 debug     [ 1563.380000] jcpcore: start
Nov 24 20:44:38 info     [ 1563.330000] usbcore: registered new interface driver sxuptp_driver
Nov 24 20:44:38 debug     [ 1563.280000] sxuptp: sxuptp_keepalive_thread start
Nov 24 20:44:37 info     read /var/tmp/hosts - 1 addresses
Nov 24 20:44:37 info     read /etc/hosts - 2 addresses
Nov 24 20:44:37 info     using nameserver 208.67.222.222#53
Nov 24 20:44:37 info     using nameserver 208.67.220.220#53
Nov 24 20:44:37 info     reading /etc/resolv.conf
Nov 24 20:44:37 info     compile time options: IPv6 GNU-getopt no-MMU ISC-leasefile no-DOCTOR no-NOWILD no-DBus no-I18N TFTP
Nov 24 20:44:37 info     started, version 2.45 cachesize 150
Nov 24 20:44:36 notice     HTTP listening on port 65535
Nov 24 20:44:36 info     [ 1556.700000] module arch cleanup sxuptp: OCM instruction memory free  of 0 @00000000
Nov 24 20:44:36 debug     [ 1556.700000] sxuptp: sxuptp_keepalive_thread stop [-512]
Nov 24 20:44:36 info     [ 1556.640000] module arch cleanup sxuptp_driver: OCM instruction memory free  of 0 @00000000
Nov 24 20:44:36 info     [ 1556.640000] usbcore: deregistering interface driver sxuptp_driver
Nov 24 20:44:36 info     [ 1556.530000] module arch cleanup jcp: OCM instruction memory free  of 0 @00000000
Nov 24 20:44:36 debug     [ 1556.530000] jcpcore: stop [-512]
Nov 24 20:44:36 debug     [ 1556.530000] jcpcore: jcpcore_recv [-512]
Nov 24 20:44:36 info     [ 1556.440000] module arch cleanup jcp_cmd: OCM instruction memory free  of 0 @00000000
Nov 24 20:44:36 debug     [ 1556.440000] jcp_command_unregister: command unregistered EXEC SCANNER DISCONNECT
Nov 24 20:44:36 debug     [ 1556.440000] jcp_command_unregister: command unregistered EXEC SCANNER CONNECT
Nov 24 20:44:36 debug     [ 1556.440000] jcp_command_unregister: command unregistered GET USB_DEVICE_LIST
Nov 24 20:44:36 debug     [ 1556.440000] jcp_command_unregister: command unregistered GET SCANNER_STATUS
Nov 24 20:44:36 debug     [ 1556.440000] jcp_command_unregister: command unregistered GET SCANNER PORT_NAME
Nov 24 20:44:36 debug     [ 1556.440000] jcp_command_unregister: command unregistered GET USB_PORT_NAME
Nov 24 20:44:36 info     [ 1556.260000] flags=0
Nov 24 20:44:36 info     [ 1556.260000] ioctl eth0, 35312
Nov 24 20:44:36 notice     klogd started: BusyBox v1.14.1 (2011-06-27 14:54:36 CST)
Nov 24 20:44:35 info     BusyBox v1.14.1