• October 29, 2025, 07:58:00 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: 1.21Build11Beta02 Problem  (Read 11847 times)

monsta

  • Level 1 Member
  • *
  • Posts: 4
1.21Build11Beta02 Problem
« on: February 26, 2009, 12:44:08 PM »
I updated to the 1.21Build11Beta02 fw & everything seemed to go ok (no obvious error messages or warnings) but after the update had completed I lost the web interface & the WLAN appears to not be functioning although the wired LAN is operational.

I am thinking I should do a factory reset, but my spidey sense keeps telling me that this may result in an un-configured white box which is unreachable via the web interface.

Anyone experienced anything similar?

monsta
Logged

EddieZ

  • Level 10 Member
  • *****
  • Posts: 2494
Re: 1.21Build11Beta02 Problem
« Reply #1 on: February 26, 2009, 02:06:55 PM »
Nope. I guess you're the first. Is wireless radio enabled?
Logged
DIR-655 H/W: A2 FW: 1.33

monsta

  • Level 1 Member
  • *
  • Posts: 4
Re: 1.21Build11Beta02 Problem
« Reply #2 on: February 27, 2009, 01:05:30 AM »
The wireless light flashes during the intial boot up, but once the unit settles it stays off & I can't access the web gui to check or change any settings.

Is a default reset always required after a fw update? If so, what is the correct procedure for a hard reset?

If that still doesn't work, is there any way of forcing firmware onto the unit i.e. TFTP/Telnet etc?

monsta
Logged

lotacus

  • Level 4 Member
  • ****
  • Posts: 450
Re: 1.21Build11Beta02 Problem
« Reply #3 on: February 27, 2009, 11:54:07 AM »
so then when your wired in and you go to the router setup, is wireless on or off?

always recommended to do a hard reset after a flash, some settings can always remain there that may conflict with updated firmware. Mine for instance, retained all wireless network settings including the SSID etc.. which shouldn't happen after a firmware update. So I had to hard reset.

You may want to see if it actually took effect.

http://routeripaddress/fw_version.html
« Last Edit: February 27, 2009, 12:00:02 PM by lotacus »
Logged

monsta

  • Level 1 Member
  • *
  • Posts: 4
Re: 1.21Build11Beta02 Problem
« Reply #4 on: February 27, 2009, 12:29:51 PM »
I couldn't access the web setup so I couldn't tell what settings were enabled.

It's all good now as a couple of hard resets have returned the web interface & I've reconfigured everything as it should be.
Logged

manman

  • Level 1 Member
  • *
  • Posts: 5
Re: 1.21Build11Beta02 Problem
« Reply #5 on: February 27, 2009, 01:01:54 PM »
you should always use wire LAN for update firmware from the beginning anyway.

after updated firmware , all seting are resetting back to default (already hard reset), so wireless connection is lossed.
Logged

EddieZ

  • Level 10 Member
  • *****
  • Posts: 2494
Re: 1.21Build11Beta02 Problem
« Reply #6 on: February 27, 2009, 02:00:27 PM »
Quote from: monsta on February 27, 2009, 12:29:51 PM
I couldn't access the web setup so I couldn't tell what settings were enabled.

It's all good now as a couple of hard resets have returned the web interface & I've reconfigured everything as it should be.

Just connecting with a ethernet cable would have given you access  ;D
Logged
DIR-655 H/W: A2 FW: 1.33

monsta

  • Level 1 Member
  • *
  • Posts: 4
Re: 1.21Build11Beta02 Problem
« Reply #7 on: February 27, 2009, 02:38:04 PM »
I did use a wired connection for the update - the problem was after updating to the new firmware (via a wired connection) I lost the web interface & the wireless access was disabled, but I still had wired access to my network & the internet.

Thanks everyone for your help
Logged