• October 30, 2025, 10:17:43 PM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: WLAN Partition Mode keeps enabling  (Read 15028 times)

rjesse

  • Level 1 Member
  • *
  • Posts: 21
WLAN Partition Mode keeps enabling
« on: August 09, 2012, 09:56:29 PM »
I'm trying to connect to from some wired clients on my network to some wireless clients.  With the wireless device connected I'm unable to ping it from the wired device.  If I restart the DAP-1360 the ping starts up, but after a while I'm unable to ping the wireless device again until I reboot the DAP-1360. Then the device is pingable for a while.

I have confirmed that WLAN Partition is not checked.  I'm running Version 2.11 Firmware, may router is an EBR-2310.

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: WLAN Partition Mode keeps enabling
« Reply #1 on: August 10, 2012, 07:08:37 AM »
Do a factory reset and manually set up the DAP using it's web page. Save settings and restart. Check the DAP settings after, is the WLAN enabled after the restart?
« Last Edit: August 10, 2012, 07:13:08 AM by FurryNutz »
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

rjesse

  • Level 1 Member
  • *
  • Posts: 21
Re: WLAN Partition Mode keeps enabling
« Reply #2 on: August 11, 2012, 08:37:11 PM »
I did the factory reset and put all my settings back.  It worked at first and then after a while I'm unable to ping any wireless devices again.

If I ping from the wireless device to the wired device then I can ping the other direction, (ie from the wired to the wireless).  But again after a while the ping stops.

Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: WLAN Partition Mode keeps enabling
« Reply #3 on: August 13, 2012, 09:19:26 AM »
I would contact DLink level 2 support and see why the WLan Partition keeps enabling after you've disabled it. Might be something between the DAP and EBR thats causing it. Keep us posted.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

rjesse

  • Level 1 Member
  • *
  • Posts: 21
Re: WLAN Partition Mode keeps enabling
« Reply #4 on: August 13, 2012, 09:52:16 AM »
I'll contact them, typically never hear back when I contact support so we'll see if that will change this time.

Rick
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: WLAN Partition Mode keeps enabling
« Reply #5 on: August 13, 2012, 09:54:18 AM »
I would call vs email. Keep us posted.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

rjesse

  • Level 1 Member
  • *
  • Posts: 21
Re: WLAN Partition Mode keeps enabling
« Reply #6 on: August 13, 2012, 12:02:08 PM »
Unfortunately no time to sit on hold this week.
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: WLAN Partition Mode keeps enabling
« Reply #7 on: August 31, 2012, 01:06:48 PM »
Any status on this?
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

rjesse

  • Level 1 Member
  • *
  • Posts: 21
Re: WLAN Partition Mode keeps enabling
« Reply #8 on: August 31, 2012, 05:51:53 PM »
Support hasn't really been of any help, their standard answer is to factory reset and reconfigure.  I have figured out that that problem has more to do with the Dlink  EBR-2310.  I bought another router and I have no problem pinging any WiFi devices, and now DHCP works properly from my WiFi clients.  Supports standard answer is to reset and rebuild the EBR-2310.  I've done that with no change.  I need to call back to support and see if they can figure out the problem, but it this point I've moved on.

Rick
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: WLAN Partition Mode keeps enabling
« Reply #9 on: August 31, 2012, 07:00:47 PM »
Good luck.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

furlong

  • Level 1 Member
  • *
  • Posts: 16
Re: WLAN Partition Mode keeps enabling
« Reply #10 on: October 21, 2012, 05:35:20 AM »
Update the wireless driver on your wireless client.
Logged