Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[User850L]

I had an older dlink router that used to work correctly with OpenDNS, and replaced it with this new DIR-850L model. I configured the DNS addresses to point to OpenDNS servers, but the WEB filtering feature is not working anymore.

I contacted their support team and they told me that it looked like my router was not using their DNS servers, although I am sure the addresses are configured correcty.

If anyone has successfully configured the DIR-850L to work with OpenDNS, please tell me the configuration settings you are using.

BTW, I am using FW v1.09.

Thanks a lot!

[FurryNutz]

Link>Welcome!

• What region are you located?
• Was a Factory Reset performed before and after any firmware updates then set up from scratch?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?
• What ISP Modem service link speeds UP and Down do you have?
• If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT and How NAT Works. To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.
• Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
• For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.

• Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
• Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
• Turn OFF DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench or try manually inputting the custom DNSs into Setup/Internet/Manual
• Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
• Ensure devices are set to auto obtain an IP address.
• If IPv6 is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
• Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI to test.
• Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
• Turn off WISH, and WPS under Advanced.
• WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
• Set current Time Zone, Date and Time. Use an NTP Server feature. Tools/Time.

[User850L]

Hi FurryNutz,

From your suggestions list, this is the configuration setting that makes Dlink's DIR-850L work with OpenDNS:

Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI to test.

I tried them one by one in sequence, but the only setting that really worked was disabling the SPI option under:

Advanced / Firewall Settings / SPI uses = unchecked

Thanks a lot!

Best Regards,
eds01

[FurryNutz]

Glad you got it working. Enjoy.