Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[imation3m]

I have DLink DSL-2750U ADSL Modem + Router, the problem is it keeps dropping connection after 4 minutes and then reconnects. I even tried on direct LAN connection with my desktop with wireless off and still it disconnects.

The ISP says, the problem is with the router.

What could be wrong?

[FurryNutz]

Link>Welcome!

• What Hardware version is your router? Look at sticker under router.
• Link>What Firmware version is currently loaded? Found on the routers web page under status.
• What region are you located?
• Are you wired or wireless connected to the router?
• Has a Factory Reset been performed?
• Was a Factory Reset performed before and after any firmware updates then set up from scratch?
• Was the router working before any firmware updates?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?
• What ISP Modem service link speeds UP and Down do you have?
• If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT and How NAT Works. To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.
  Example of a D-Link router configured for PPPoE with ISP Modem bridged: PPPoE Configuration on Router
• Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
• For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.

• Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS or Gamefuel.
• Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
• Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
• Turn on DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench
• Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
• Ensure devices are set to auto obtain an IP address.
• If IPv6 is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
• Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI to test.
• Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
• Turn off WISH, and WPS under Advanced.
• WAN Port Speed set to Auto or specific speed? Some newer ISP modems support 1000Mb so manually setting to Gb speeds can be supported by the router. Advanced/Advanced Networking/WAN Port Speed
• Set current Time Zone, Date and Time. Use an NTP Server feature. Tools/Time.
• Check cable between Modem and phone line box and phone pole, swap out to be sure. Ensure the phone line signal is to spec and in good condition. Have your ISP check the lines and signal. Modes are dependent upon having a good signal.

Wireless Configurations
Links>Wireless Installation Considerations and Managing Signal Congestion and Good Neighbour Policy

• Ensure the default (dlink) SSID name is changed. Can be anything and not something thats already in use by any neighboring WiFi routers. Under Setup/Wireless/Manual.
• What wireless modes are you using?
• 2.4Ghz Routers only:[/b] Try single mode G or N or mixed G and N?
• Channel Width set for Auto 20/40Mhz or try 20Mhz only.
• Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear.
• What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
• What wireless devices do you have connected?
• Any cordless house phones?
• Any other WiFi routers in the area? Link> Use InSSIDer to find out. How many?
• If you have any of these options, Try turning OFF or ON Short GI, WLAN Partition, HT 20/40 Co-exhistance and Extra Wireless Protection if you have it. Recommended settings are default. Under Advanced/Advanced Wireless.
• Enable WMM Enable Under Advanced/Advanced Wireless.
• Try setting Medium or Low power output settings and test again Under Advanced/Advanced Wireless.