Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[simdash]

I am using a DIR 615 N 300 router and it sometimes gives a lower speed. The firmware driver has been upated to its latest, and its WPA2 protected.
Sometimes when testing the speed through Speedtest.net the router gives a much slower speed than when using a direct cable for connection. For example a Ping will be 1200 while through cable it gives 3-5 ms, and download speed to 1.7 and it can not even show any upload speed, while through cable gives 10-12 mbps.

Most of the time it gives a very good speed even there are several devices connected to it, and sometimes it loses connection and need to restart the router.
We have both laptops with Win 7 + 8, smartphones and an IP phone connected to this router, without using it for downloading or streaming TVs, just for the casual use as most people do.
 
I was wondering if anyone have any ideas on how to improve the speed.

Any helps are highly appreciated.

[FurryNutz]

Link>Welcome!

• What Hardware version is your router? Look at sticker under router.
• Link>What Firmware version is currently loaded? Found on the routers web page under status.
• What region are you located?
• Are you wired or wireless connected to the router?
• Has a Factory Reset been performed?
• Was a Factory Reset performed before and after any firmware updates then set up from scratch?
• Was the router working before any firmware updates?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?
• What ISP Modem service link speeds UP and Down do you have?
• If this modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT and How NAT Works. To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.
  Example of a D-Link router configured for PPPoE with ISP Modem bridged: PPPoE Configuration on Router
• Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
• For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.

Router and Wired Configurations
Some things to try: - Log into the routers web page at 192.168.0.1. Use IE, Opera or FF to manage the router.

• Turn off ALL QoS or Disable Traffic Shaping (DIR only) GameFuel (DGL only and if ON.) options, Advanced/QoS or Gamefuel.
• Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual or under Setup/PARENTAL CONTROL/Set to>None: Static IP or Obtain Automatically From ISP.
• Enable Use Unicasting (compatibility for some ISP DHCP Servers) under Setup/Internet/Manual.
• Turn OFF DNS Relay under Setup/Networking. Link>Finding Faster DNS Addresses using Name Bench
• Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting.
• Ensure devices are set to auto obtain an IP address.
• If IPv6 is an option on the router, select Local Connection Only or Disable IPv6 options under Setup/IPv6.
• Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall. Enable or Disable SPI to test.
• Enable uPnP and Multi-cast Streaming under Advanced/Networking. Disable uPnP for testing Port Forwarding rules. Enable IPv6 Multi-cast Streaming for routers that have a Media Server option. Disable IPv6 Multi-cast Streaming if IPv6 or Media Server is not being used.
• Turn off WISH, and WPS under Advanced.
• Set current Time Zone, Date and Time. Use an NTP Server feature. Tools/Time.
• Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended.

Also we recommend only speed testing on wired LAN connections as testing on wireless can produce invalid results due to many variables with wireless...

[FurryNutz]

Any status on this? 

[FurryNutz]

http://forums.dlink.com/index.php?topic=58647.0