Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[nashwalker]

Hi, iv been trying to configure my 4500 again due to Nat issues. I have followed the guide that is set for 360 users and have still been having issues. Also, is there anyway that I can actually check to see if the ports are opened that I have instructed the router to open? Such as web sites or apps?

[FurryNutz]

Link>Welcome!

• What Hardware version is your router? Look at sticker under router.
• Link>What Firmware version is currently loaded? Found on the routers web page under status.
• What region are you located?
• Are you wired or wireless connected to the router?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?
• Is ISP Modem/Service using Dynamic or Static WAN IP addressing?
• What ISP Modem service link speeds UP and Down do you have?

What generation is your xbox? Slim?

[nashwalker]

hardware is a2/ firmware is 1.23na but originally was 1.21n a. i live in north texas and my isp is twc Motorola surfboard

i am wired for my xbox only, mac, ps3, iPad and two iPhones are wireless

sbg6580 model #/ dynamic or static wan ip addressing? if you mean i have all of my devices set on static ip but I'm not sure if thats what you are asking.

download is 20 and up is either 2 or 5 and i have a matte black slim s

thanks again

[FurryNutz]

hardware is a2/ firmware is 1.23na but originally was 1.21n a. i live in north texas and my isp is twc Motorola surfboard

i am wired for my xbox only, mac, ps3, iPad and two iPhones are wireless

sbg6580 model #
If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT and How NAT Works. To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Refer to the ISP or Mfr of the modem for additional information.

if you mean i have all of my devices set on static ip but I'm not sure if thats what you are asking.

• Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking. This ensures each devices gets its own IP address when turned on and connected, eliminates IP address conflicts and helps in troubleshooting and maintain consistency for applications that need to connect as well as mapped drives.
• Ensure devices are set to auto obtain an IP address.

download is 20 and up is either 2 or 5 and i have a matte black slim s
How do you have GameFuel set up? It should be using the single Xbox rule.

Have you done a factor reset on the Xbox Slim under Dash Board/Networking/Wired/Configure/2nd tab over/Factory Reset?

[nashwalker]

everything you just mentioned is how it is. iv played a few games of halo 3 and the connection is good. so my next question is how can i check to ensure the ports that i have forwarded are open? i have the xbox set up in gamer fuel. also the modem is successfully bridged. the number is the same as my external ip address. thanks

[FurryNutz]

if all is set up well, you should be seeing NAT OPEN in the status. I can't remember how in Halo 3, I think there is a status information in one of the option windows. Do you have a different game like CoD or maybe Halo 4?

[nashwalker]

It's saying it's open. And the games are fine now. But is there anyway to ensure that the ports are open?

[FurryNutz]

Thats all you need to check for...If it's OPEN then your good. Some games have this NAT checking feature.

Should work for you well now. Enjoy.

[nashwalker]

thanks again man

[FurryNutz]

  Anytime, come back and visit if needed.