Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[Songbird]

Hi.  I hope I'm posting this message at the right place for I couldn't find the board for this model.

Been having connection problems oft and on since I started using the router almost one year.  Sometimes it runs
well for several days and then comes the bad phase when it briefly & periodically keeps getting disconnected and connected.
A couple of days ago it got disconnected and didn't connect at all, until I unplugged and replugged the power cord.  Then it
began working but the brief disconnections persist. 

I was told that perhaps I need to get an update of the firmware of my router model.  Any information on that please?

Your feedback and necessary guidelines would be helpful.   Thanks.

[FurryNutz]

Link>Welcome!

• What Hardware version is your router? Look at sticker under the router case.
• Link>What Firmware version is currently loaded? Found on the routers web page under status.
• What region are you located?

Internet Service Provider and Modem Configurations

• What ISP Service do you have? Cable or DSL?
• What ISP Modem Mfr. and model # do you have?

Wireless Configurations
Links>Wireless Installation Considerations and Managing Signal Congestion and Good Neighbour Policy

• Ensure the default (dlink) SSID name is changed. Ensure that different SSID names are used between each WiFi 2.4/5Ghz radios. Can be anything and not something that's already in use by any neighbouring WiFi routers. Under Setup/Wireless/Manual.
• What wireless modes are you using?
• Channel Width set for Auto 20/40Mhz or try 20Mhz only.
• Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions.
• What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
• What wireless devices do you have connected?
• Ensure any devices with WiFi adapter drivers are updated.
• Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by that maybe causing interferences?
• Any other WiFi routers in the area that maybe causing interferences? Link> Use InSSIDer to find out. How many? Use v3, its free.
• If you have any of these options, Try turning OFF or ON Short GI, WLAN Partition, Extra Wireless Protection and HT 20/40 Co-existence if you have it. Also testing with HT20/40Mhz Co-existence enabled will impact results as well. I prefer to use this option OFF. Recommended settings are default. Under Advanced/Advanced Wireless.

Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
http://www.smallnetbuilder.com/wireless/wireless-basics/31083-smallnetbuilders-wireless-faq-the-essentials

[Songbird]

Hi!  Not sure if I would know answers to all questions.

Version on router case sticker says H/W Ver.A1  F/W Ver 1:00.

No idea which Firmware version is presently loaded.  Nor do I know how to locate to locate the router webpage.  However, the router was
purchased last June, if that may help. 

I'm using DSL service.   Modem name/model Comtrend CT-5072T.

Router placement is close to the computer on the same table next to the modem.   No electronics close by. 

Just wondering, could there be a problem with the surge protector I'm using.  It looks okay from the outside but it's an old one, about 10 yrs or more.

[FurryNutz]

Found on the routers web page under status.

What region are you located?

Try in a different area...

• By-pass the main host router and check internet connection by connecting a wired LAN PC directly to the ISP modem to verify connection access and ISP speeds.
• Check cable between Modem and Router, swap out to be sure. Link> Cat6 is recommended.
• Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask. Link>Checking MTU Values
• For DSL/PPPoE connections on the router, ensure that "Always ON" option is enabled.
• If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>Double NAT and How NAT Works. Call the ISP and ask to see if the ISP modem can be bridged. To tell if the modem is bridged or not, look at the routers web page, Status/Device Info/Wan Section, if there is a 192.168.0.# address in the WAN IP address field, then the modem is not bridged. If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Also check the routers DHCP IP address maybe conflicting with the ISP modems IP address of 192.168.0.1. Check to see if this is the same on the ISP modem, and if modem can't be bridged, change the DIR router to 192.168.1.1 or .0.254.
  Example of a D-Link router configured for PPPoE with ISP Modem bridged: PPPoE Configuration on a Router

[Songbird]

I'm located in Canada.   Thanks for the suggestions.  I'll try whatever I can and then let you know soon. 

[FurryNutz]