Print

Please login or register.
1 Hour 1 Day 1 Week 1 Month Forever
Login with username, password and session length

[dentizt]

Hey everybody,
since yesterday i am facing a problem with my DSR 1000N Router. I upgraded to the latest firmware FW202B8 and in my opinion everything was fine. The router restarted and after Login, the router crashes and i cant reach it anymore. Power Plug off and i tried again....same problem...push Reset button for 10 sek. ...same problem!

Power LED ist solid amber/orange (Device during power-on process) and 2,4 GHz LED is blinking. Link LED are solid green and amber. I have no idea what to do.

Could anybody help?

Thanks

My Setup: Windows 7 Pro 64bit, Gigabit Ethernet, latest Firefox

[FurryNutz]

Link>Welcome!

• What region are you located?
• Are you wired or wireless connected to the router?
• Was a Factory Reset performed before and after any firmware updates then set up from scratch?

  Link> >FW Update Process


I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this. We find that phone contact has better immediate results over using email.
Let us know how it goes please.

[dentizt]

Hey!

--> region is europe
--> i am wired
--> factory reset was performed but with no result

From Dlink Support i received a recovery manual and firmware, tried to flash via console, tftp and putty but it brought this result:


setting up hardware watchdog timer... Done
/sbin/rc: ./switchdriverInit: 47: -1: not found
Inserting the bcm debug module...Done
Inserting the power saving module...Done
Starting NIMF daemon... Done


U-Boot 1.1.1 (Development build, svnversion: exported) (Build time: Mar 22 2010                                                                                         - 12:14:14)

Warning: Board descriptor tuple not found in eeprom, using defaults
CUST_DSR1000 board revision major:2, minor:0, serial #: unknown
OCTEON CN5010-SCP pass 1.1, Core clock: 500 MHz, DDR clock: 200 MHz (400 Mhz dat                                                                                        a rate)
DRAM:  256 MB
Flash: 32 MB
Clearing DRAM...... done
BIST check passed.
Starting PCI
PCI Status: PCI 32-bit
PCI BAR 0: 0x00000000, PCI BAR 1: Memory 0x00000000  PCI 0xf8000000
Net:   octeth0, octeth1, octeth2

Hit any key to stop autoboot:  0
D-Link DSR-1000N bootloader#
D-Link DSR-1000N bootloader#
D-Link DSR-1000N bootloader#
D-Link DSR-1000N bootloader#
D-Link DSR-1000N bootloader#
D-Link DSR-1000N bootloader#
D-Link DSR-1000N bootloader# setenv ipaddr 192.168.10.1
D-Link DSR-1000N bootloader# setenv serverip 192.168.10.123
D-Link DSR-1000N bootloader# setenv ethact octeth0
D-Link DSR-1000N bootloader# setenv firm_flash 'erase BDCA0000 BF99FFFF; cp.b 0x                                                                                        aa00000 BDCA0000 1D00000'
D-Link DSR-1000N bootloader# setenv boot_firm 'cp.b  BDCA0000 0xaa00000 900000;                                                                                         bootoctlinux 0xaa00200 mtdparts=phys_mapped_flash:640k(bootloader)ro,9M(kernel),                                                                                        20M(rootfs),2M(AppConfig),128k(bootload-env)'
D-Link DSR-1000N bootloader# setenv bootcmd 'run boot_firm'
D-Link DSR-1000N bootloader# saveenv
Saving Environment to Flash...
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... ..done
Protected 1 sectors
D-Link DSR-1000N bootloader# tftp 0xAA00000 \\192.168.10.123\DSR-1000N_A1_FW202B                                                                                        B01C
Interface 0 has 3 ports (RGMII)
Using octeth0 device
TFTP from server 192.168.10.123; our IP address is 192.168.10.1
Filename '192.168.10.123DSR-1000N_A1_FW202BB01C'.
Load address: 0xaa00000
Loading: octeth0: Up 1000 Mbps Full duplex (port  0)

TFTP error: 'File not found' (1)
Starting again

Using octeth1 device
TFTP from server 192.168.10.123; our IP address is 192.168.10.1
Filename '192.168.10.123DSR-1000N_A1_FW202BB01C'.
Load address: 0xaa00000
Loading: octeth1: Up 1000 Mbps Full duplex (port  1)
T T T T T T
Abort
WARNING: Data loaded outside of the reserved load area, memory corruption may oc                                                                                        cur.
WARNING: Please refer to the bootloader memory map documentation for more inform                                                                                        ation.
D-Link DSR-1000N ' - try 'help'NTERRUPT>
D-Link DSR-1000N bootloader#
D-Link DSR-1000N bootloader# tftp 0xAA00000 DSR-1000N_A1_FW202BB01C
Using octeth0 device
TFTP from server 192.168.10.123; our IP address is 192.168.10.1
Filename 'DSR-1000N_A1_FW202BB01C'.
Load address: 0xaa00000
Loading: #################################################################
         #################################################################
         #######################################
done
Bytes transferred = 24068096 (16f4000 hex), 10331 Kbytes/sec
D-Link DSR-1000N bootloader# run firm_flash

................................................................................                                                                                        ................................................................................                                                                                        ........................................................................ done
Erased 232 sectors
Copy to Flash... ...............................................................                                                                                        ................................................................................                                                                                        ................................................................................                                                                                        ................................................................................                                                                                        ................................................................................                                                                                        ................................................................................                                                                                        .done
D-Link DSR-1000N bootloader# run boot_firm
argv[2]: mtdparts=phys_mapped_flash:640k(bootloader)ro,9M(kernel),20M(rootfs),2M                                                                                        (AppConfig),128k(bootload-env)
ELF file is 64 bit
Attempting to allocate memory for ELF segment: addr: 0xffffffff80130000 (adjuste                                                                                        d to: 0x0000000000130000), size 0x7e3030
Allocated memory for ELF segment: addr: 0xffffffff80130000, size 0x7e3030
Loading .text @ 0xffffffff80130000 (0xd0 bytes)
Loading .text.nofill @ 0xffffffff801300d0 (0x8 bytes)
Loading .text.error @ 0xffffffff801300d8 (0x38 bytes)
Loading .text.rc_read @ 0xffffffff80130110 (0x80 bytes)
Loading .text.rc_get_bit @ 0xffffffff80130190 (0x178 bytes)
Loading .text.malloc @ 0xffffffff80130308 (0xd8 bytes)
Loading .text.decompress_kernel @ 0xffffffff801303e0 (0x1230 bytes)
Loading .text.puts @ 0xffffffff80131610 (0x8 bytes)
Loading .text.puthex @ 0xffffffff80131618 (0x8 bytes)
Loading .text.main @ 0xffffffff80131620 (0x8 bytes)
Loading .MIPS.options @ 0xffffffff80131628 (0xa0 bytes)
Loading .rodata.str1.8 @ 0xffffffff801316c8 (0x130 bytes)
Loading .data @ 0xffffffff80132000 (0x3df000 bytes)
Clearing .bss @ 0xffffffff80511000 (0x402030 bytes)
## Loading Linux kernel with entry point: 0xffffffff80130000 ...
Bootloader: Done loading app on coremask: 0x1
Linux version 2.6.32.13-Cavium-Octeon (avantikar@build-server1) (gcc version 4.3                                                                                        .3 (Cavium Networks Version: 2_0_0 build 95) ) #1 Fri Oct 23 10:53:56 IST 2015
CVMSEG size: 2 cache lines (256 bytes)
Cavium Networks SDK-2.0
bootconsole [early0] enabled
CPU revision is: 000d0601 (Cavium Octeon+)
Checking for the multiply/shift bug... no.
Checking for the daddiu bug... no.
Determined physical RAM map:
 memory: 0000000000231000 @ 000000000103f000 (usable after init)
 memory: 000000000ec00000 @ 0000000001300000 (usable)
Wasting 232904 bytes for tracking 4159 unused pages
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  DMA32    0x0000103f -> 0x00100000
  Normal   0x00100000 -> 0x00100000
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x0000103f -> 0x00001270
    0: 0x00001300 -> 0x0000ff00
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60141
Kernel command line:  bootoctlinux 0xaa00200 mtdparts=phys_mapped_flash:640k(boo                                                                                        tloader)ro,9M(kernel),20M(rootfs),2M(AppConfig),128k(bootload-env) console=ttyS0                                                                                        ,115200
PID hash table entries: 1024 (order: 1, 8192 bytes)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Primary instruction cache 32kB, virtually tagged, 4 way, 64 sets, linesize 128 b                                                                                        ytes.
Primary data cache 16kB, 64-way, 2 sets, linesize 128 bytes.
Memory: 237312k/243908k available (4966k kernel code, 6236k reserved, 1555k data                                                                                        , 2244k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:408
Calibrating delay loop (skipped) preset value.. 1000.00 BogoMIPS (lpj=2000000)
Mount-cache hash table entries: 256
Checking for the daddi bug... no.
NET: Registered protocol family 16
Enabling Octeon big bar support
PCI Status: PCI 32-bit
PCI Clock: 33 MHz
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:03.0: PME# supported from D0 D3hot
pci 0000:00:03.0: PME# disabled
Switching to clocksource OCTEON_CVMCOUNT
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 2, 16384 bytes)
TCP established hash table entries: 8192 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
/proc/octeon_perf: Octeon performace counter interface loaded
octeon_wdt: Initial granularity 5 Sec.
HugeTLB registered 2 MB page size, pre-allocated 0 pages
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 464
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1180000000800 (irq = 58) is a OCTEON
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
brd: module loaded
loop: module loaded
mdio-octeon: probed
mdio-octeon mdio-octeon.0: Version 1.0
Intel(R) PRO/1000 Network Driver - version 7.3.21-k5-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
sky2 driver version 1.25
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.5
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
OcteonUSB: Detected 1 ports
OcteonUSB OcteonUSB.0: Octeon Host Controller
OcteonUSB OcteonUSB.0: new USB bus registered, assigned bus number 1
OcteonUSB OcteonUSB.0: irq 80, io mem 0x00000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
OcteonUSB: Registered HCD for port 0 on irq 80
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-onetouch
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
i2c /dev entries driver
rtc-ds1307 0-0068: rtc core: registered ds1337 as rtc0
i2c-octeon i2c-octeon.0: version 2.0
oprofile: using mips/octeon performance monitoring.
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    Performance counters on
    Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1856 buckets, 7424 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ctnetlink v0.93: registering with nfnetlink.
xt_time: kernel timezone is -0000
GRE over IPv4 demultiplexor driver
ip_tables: (C) 2000-2006 Netfilter Core Team
ipt_account 0.1.7 : Piotr Gasid¦o <quaker@barbara.eu.org>, http://www.barbara.eu                                                                                        .org/~quaker/ipt_account/
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Bridge firewalling registered
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
L2 lock: TLB refill 256 bytes
L2 lock: General exception 128 bytes
L2 lock: low-level interrupt 128 bytes
L2 lock: interrupt 640 bytes
L2 lock: memcpy 1152 bytes
Bootbus flash: Setting flash for 32MB flash at 0x1dc00000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
phys_mapped_flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
Creating 7 MTD partitions on "phys_mapped_flash":
0x000000000000-0x0000000a0000 : "bootloader"
0x0000000a0000-0x0000005a0000 : "kernel"
0x0000005a0000-0x000001aa0000 : "rootfs"
0x000001aa0000-0x000001da0000 : "PackageManager"
0x000001da0000-0x000001fa0000 : "AppConfig"
0x000001fa0000-0x000001fe0000 : "EMPTY"
0x000001fe0000-0x000002000000 : "bootload-env"
usb 1-1: new high speed USB device using OcteonUSB and address 2
Freeing unused kernel memory: 2244k freed
/sbin/rc starting
Booting DSR User Space...

Mounting file systems
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
empty_blocks 0, bad_blocks 0, c->nr_blocks 24
mount: Mounting /dev/mtdblock3 on /pkgMgmt failed: Input/output error
Mounting config partition failed.
Will erase partition and retry.
Erased 3072 Kibyte @ 0 -- 100% complete.
Mounting config partition
fuse init (API version 7.13)
octeon-ethernet 2.0
Interface 0 has 3 ports (RGMII)
Sysctl registeration for hardware offload control suceed
productData: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
Initialzing Product Data modules
Loading LED driver
bwMonitor sysctl registered
CONFIG_SYSCTL enabled ...
Initialized bandwidth monitor ...
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapter                                                                                        s
Enabling Quiet Boot...Done
Setting up loopback
Setting mac address for LAN/WAN1/WAN2
Setting Hostname... Done.
setting Host name.
setting hostname as DSR-1000N
/
wan3 related
Starting pnac daemon...Done
Loading WLAN Modules...Done
Starting dot11 daemon...Done
Initializing the Management componentLuaSQL: library routine called out of seque                                                                                        nce: 1610612735 Unknown error occurred
Done
net.ipv6.conf.eth1.accept_ra = 0
net.ipv6.conf.eth2.accept_ra = 0
net.ipv6.conf.eth1.router_solicitations = 0
net.ipv6.conf.eth2.router_solicitations = 0
cp: /pkgMgmt/www/db/*: No such file or directory
Creating Dummy Config File
Starting linkmonitor daemonDone
Inserting ipset modules...Done
inserting default firewall rules
inserting default firewall6 rules
teamf1.cfg.ascii
teamf1.cfg.ascii
Restoring configuration from persistant storage...
cpAcc.db             en_US.db             system.db
data                 solution_snort.conf  system.sql
dhScript.sh          stats.db             teamf1.cfg.ascii
dummy.file           stats.sql            wcfClientd.conf
making database from system settings...
restore file: /tmp/teamf1.cfg.ascii
importing...
setting up hardware watchdog timer... Done
/sbin/rc: ./switchdriverInit: 47: -1: not found
Inserting the bcm debug module...Done
Inserting the power saving module...Done
Starting NIMF daemon... Done
creating smtpAlg device
Creating /dev/smtpAlg
starting firewalld Daemon...Done
Starting IKE Daemon...Done
Done
Starting VPN KEEP ALIVE Daemon...Done
Restoring certficates from persistant storage...Done
ls: /pkgMgmt/control/: No such file or directory
SSLVPN Intialization .......  Done
Webserver Starting....Octeon_init success
Done
Copying Default Login Images...Getting firmware version...Done
Making Brand.conf...
Done creating Brand.conf
Starting status monitor daemonDone
Copying necessary files for PPTP Server...
Done
Initializing 3G... Done
starting ntpd Daemon...Done
ipset v4.2: Unknown set
ipset v4.2: Unknown set
Loading WpsPB Module..Initialzing Wps module
starting SNMP Daemon...Done
Starting the cron deamon...Done
Creating /dev/pts/0 pseudo device for L2TP <-> PPP communication... Done
Bandwidth Profile Initialization...Cannot find device "eth0.4088"
Cannot find device "eth0.4088"
Done
OPENVPN Intialization .......Auth Intialization .......  starting auth daemon
Done
Starting captivePortal daemon... Done
net.bridge.bridge_mode_state = 0
cp: /pfrm2.0/var/sla.txt: No such file or directory
Starting CP Accounting daemon... Done
Starting intelAmt daemon... Done
Starting the LM deamon...Done
Loading Factory Defaults ModulesInitialzing Factory defaults modules

The router didnt start after flash, problem was the same!!!!!

Any ideas?

[FurryNutz]

Can you ping the routers IP address after you load the FW and do a reboot or power cycle? Do you get an IP address on the wired PC?

I would get D-Link support on the phone and reference this thread. Seems like the file is loading. Just getting hung up after some where and not coming to ready.