• November 01, 2024, 09:33:52 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Fujifilm X100T cannot connect  (Read 3665 times)

peterlongfield

  • Guest
Fujifilm X100T cannot connect
« on: March 21, 2018, 05:16:26 PM »

My Camera Cannot connect to the router (DIR-813) - WPD or SSID/PAssword.
I can see its mac address appearing in the list of wireless devices during the connection attempts, but the camera screen is stuck on an hourglass icon, then reverts to "failed connection" after a minute or two and the mac address disappears then.
I am confident in the password for the SSID access - and I have tried WPS too with button or with PIN...

The camera connects fine to my phone's Wifi Hotspot so I know the camera is fine.

Anybody has succeeded in doing that?
 
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Fujifilm X100T cannot connect
« Reply #1 on: March 21, 2018, 05:53:20 PM »

Link>Welcome!

  • What Hardware version is your router? Look at sticker under the router case.
  • Link>What Firmware version is currently loaded? Found on the routers web page under status.
  • What region are you located?
  • Are you wired or wireless connected to the router?
  • Has a Factory Reset been performed?
  • Was a Factory Reset performed before and after any firmware updates then set up from scratch?
  Link> >FW Update Process
  • Was the router working before any firmware updates?

Internet Service Provider and Modem Configurations
  • What ISP Service do you have? Cable or DSL?
  • What ISP Modem Mfr. and model # do you have?

Wireless Configurations
Links>Wireless Installation Considerations and Managing Signal Congestion and Good Neighbour Policy
  • Ensure the default (dlink) SSID name is changed. Ensure that different SSID names are used between each WiFi 2.4/5Ghz radios. Can be anything and not something that's already in use by any neighbouring WiFi routers. Under Setup/Wireless/Manual.
  • What wireless modes are you using?
  • 2.4Ghz and 5Ghz routers: Try single mode G or N or mixed G and N on 2.4Ghz and single mode N or AC on 5Ghz?
  • Channel Width set for Auto 20/40Mhz or try 20Mhz only.
  • Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions. Try channel 48 or 149 on 5Ghz.
  • What security mode are you using? Preferred security is WPA-Personal. WPA2/AES Only. Some WiFi adapters don't support AES, so you might want to try TPIK only or Auto TPIK and AES.
  • If you have any of these options, Try turning OFF or ON Short GI, WLAN Partition, Extra Wireless Protection and HT 20/40 Co-existence if you have it. Also testing with HT20/40Mhz Co-existence enabled will impact results as well. I prefer to use this option OFF. Recommended settings are default. Under Advanced/Advanced Wireless.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.