• February 21, 2025, 10:13:06 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Firmware update impossible from 3.11 to 3.12 or 3.14  (Read 19248 times)

scoody

  • Level 1 Member
  • *
  • Posts: 19
Firmware update impossible from 3.11 to 3.12 or 3.14
« on: October 16, 2019, 05:43:08 AM »
Hi,

My hardware is version A1 , my firmware is 3.11_WW.

If i try to upgrade in DSR-1000AC_Ax_FW3.12B101H_WW putting firware on usb drive, i'have a message "operation not supported"

if i try to update by PC with same FW or also last one  DSR-1000AC_Ax_FW3.14_WW , i have a message Firmware is NOT available to be installed in NON-Supported Hardware machine, please use correct firmware version for your devices.


Seams i try to use the good one .... No ???

Best Regards and thanks for your help
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Firmware update impossible from 3.11 to 3.12 or 3.14
« Reply #1 on: October 16, 2019, 02:17:06 PM »
Does the release notes for the FW updates give any information about how to update or what needs to be done to effect the update?

I recommend that you phone contact your regional D-Link support office and ask for help and information regarding this.
Link> Tech Support Contact Information
We find that phone contact has better immediate results over using email.
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

petshop88

  • Level 1 Member
  • *
  • Posts: 4
Re: Firmware update impossible from 3.11 to 3.12 or 3.14
« Reply #2 on: November 15, 2021, 01:48:59 AM »
Hi,

You must make sure you get the correct matching hardware model firmware. Then upgrade using a web access, one version at a time, from 3.11 -> 3.12 -> 3.13 -> 3.14 -> 3.17 -> 3.17 Hotfix.

I have successfully upgraded DSR 1000AC & 500N using firmware downloaded from:
http://support.dlink.com.au/

Thank you.

Sincerely,
Petshop88
Logged

FurryNutz

  • Poweruser
  •   ▲
    ▲ ▲
  • *****
  • Posts: 49923
  • D-Link Global Forum Moderator
    • Router Troubleshooting
Re: Firmware update impossible from 3.11 to 3.12 or 3.14
« Reply #3 on: November 16, 2021, 08:28:17 AM »
Hopefully they have updated there unit by now since this was posted back in 2019.  ;)
Logged
Cable: 1Gb/50Mb>NetGear CM1200>DIR-882>HP 24pt Gb Switch. COVR-1202/2202/3902,DIR-2660/80,3xDGL-4500s,DIR-LX1870,857,835,827,815,890L,880L,868L,836L,810L,685,657,3x655s,645,628,601,DNR-202L,DNS-345,DCS-933L,936L,960L and 8000LH.

scoody

  • Level 1 Member
  • *
  • Posts: 19
Re: Firmware update impossible from 3.11 to 3.12 or 3.14
« Reply #4 on: December 07, 2022, 03:39:57 AM »
unfortunatly, years after years i didn't succeed, and now i have troubles with TLS version, need to upgrade certificate.

The answer was here :

DSR1000AC firmware support universal firmware for the different hardware version from v3.12.
There are two firmware upgrade steps for firmware version v3.12.
Please upgrade firmware from v3.12B101.
If your device’s firmware is earlier than 3.12, please upgrade corresponding firmware based your device hardware version.
Please follow the upgrade procedure in case fault caused during firmware upgrade.
1. Please check HW version on device UI first.
 2. Select the corresponding intermediate and common firmware version for upgrade
 process.
Intermediate firmware
DSR-1000_B1_FW3.11B001E_WW/RU
DSR-1000AC_A1_FW3.11B001E_WW/RU
Common firmware
DSR-1000_Bx_FW3.12B101H_WW/RU
DSR-1000AC_Ax_FW3.12B101H_WW/RU


i upgraded from my 3.11 with DSR-1000AC_A1_FW3.11B001E_WW
Logged