• May 23, 2025, 01:54:59 AM
  • Welcome, Guest
Please login or register.

Login with username, password and session length
Advanced search  

News:

This Forum Beta is ONLY for registered owners of D-Link products in the USA for which we have created boards at this time.

Author Topic: Losing connection to modem  (Read 4719 times)

stogs

  • Level 1 Member
  • *
  • Posts: 5
Losing connection to modem
« on: September 19, 2009, 07:35:18 AM »
I am losing connection from my router to the modem, it happens several times throughout the day.  I have to either wait a few minutes or restart the router to get my internet connection back.  I have the DNS relay turned off, is this the freezing issue that people are reporting?

Thanks.
Logged

EddieZ

  • Level 10 Member
  • *****
  • Posts: 2494
Re: Losing connection to modem
« Reply #1 on: September 19, 2009, 10:51:43 AM »
IMHO the "DNS relay" issue solution is bogus on 1.3x.

Could you post both the logs from router and modem?
« Last Edit: September 20, 2009, 09:31:13 AM by EddieZ »
Logged
DIR-655 H/W: A2 FW: 1.33

rdubs

  • Level 1 Member
  • *
  • Posts: 21
Re: Losing connection to modem
« Reply #2 on: September 19, 2009, 11:26:11 AM »
I am having the same problem until I turned of WISH Wireless Intelligence Stream Handling. I did this two days ago and have had no more problems. I would try that and see how it goes.
Logged

rosybaumster

  • Level 1 Member
  • *
  • Posts: 1
Re: Losing connection to modem
« Reply #3 on: September 27, 2009, 06:03:58 PM »
Hey, I've been having the same issue as well. rdubs, has the internet been fine after disabling WISH?
Logged

junkun13

  • Level 1 Member
  • *
  • Posts: 6
Re: Losing connection to modem
« Reply #4 on: September 27, 2009, 09:09:01 PM »
I'm experiencing this too, I'll try to disable WISH too. hope that solves the problem
Logged

Whitestar

  • Level 1 Member
  • *
  • Posts: 1
Re: Losing connection to modem
« Reply #5 on: October 01, 2009, 08:02:08 PM »
Hi Stogs & others who have similar problem,

If I may suggest, try looking @ this site: http://support.microsoft.com/kb/940266

& maybe investigate the relationship between the Nat features of the router & the

" netsh interface tcp show global " attrbs.

Here are the settings I am using on a test system:

http://yfrog.com/3dimage3qkj

I have found many of the suggestions in this forum helpful, but  I have also had to experiment w/ a number of settings ( router wise & thru Windows, I have a Vista setup ) to find a correct balance.

I am not sure if this will help u, but here are some of my settings I think may be of interest to u.


- Firmware: 1.32NA
- Advanced DNS - Disabled
- QOS - engine - disabled
- QOS - Traffic Shaping - disabled
- QOS - Auto Uplink Speed - disabled
- QOS - Auto classification - disabled
- QOS - Dynamic Fragmentation - disabled
- Manual uplink speed - 2048 kbps
- Firewall Settings - SPI - disabled ( Have software firewall configured )
( the SPI disabled is a experiment, some NAT/SPI enabled routers do not play well w/ Vista, in my case )
- Wan Port Speed - 1000Mbps

Using these settings I have seen speeds of over 2000kb/sec


Hope this helps

-  Tom









Logged